User manual PYLE PLVWR7300 Install Guide

[. . . ] Specifications ------------------------------------------------------- 10 15. TV TUNER BOX -----------------------------------------------------11 16. Remote Control Function --------------------------------------------11 17. Tuner Intstallation and Electrical Connections --------------------12 18. [. . . ] When there is smoke or peculiar smell in use, unplug the power cord immediately and send it to your local dealer or our service center. When there is damage to the LCD monitor casing, send it to your local dealer or our service center. Do not use this LCD monitor in areas susceptible to excessive dust, dirt, and humid. Do not install the LCD monitor in areas that are exposed to direct sunlight, extreme heat, and extreme cold environment. Do not expose the LCD monitor to rain or moisture. 2 Package This LCD monitor comes with all the items below. Contact your dealer immediately if anything is missing. * 20" High RES TFT-LCD Wide Screen Monitor * Overhead Console Mounting Bracket * Credit Card Size Remote Control with Batteries * Interface Cable with RCA jacks for Audio / Video Connection and 12V DC * User's Manual * Warranty Card * Infrared Wireless Headphone User Control Overview * Panel Control POWER MENU UP DOWN 3 Function Descriptions * Power: * Menu: * / You may also turn the monitor on and off with the "Power" button. Press the "MENU" button to pop up the OSD menus. Keys: 1. Make item selection in OSD menus to increase or decrease parameters as well. Press the "Mute" button from the remote control to turn off the sound of the LCD monitor. * Mute: Start Your Installation * Monitor connection 4 Setting Up The Dome Lamps *Operating the dome Lamps 1. There are three function buttons for the Dome lamps operation: OFF, DOOR, and ON. ON: To turn on the lamps. ON OFF DOOR ON OFF DOOR * The electric circuit figure OFF W B DOOR ON LAMPS R BATTERY + Point Power Cord Color R W B Red White Black Connection Connecting With Power Supply Connecting With Sensor of Car Doors For Ground Connection * Remarks: 1. Make all required audio, video and power connections to the appropriate connectors on the tuner as indicated in the drawing below to suit your system installation. Install the infrared remote eye in a location you know will be Installation in line-of-sight with the remote control use location Please note that the drawing below describes connections for all system possibilities and your particular system may vary from this. For example, if your car radio lacks AUX line level input jacks, you will be unable use the A/V VIDEO OUT jacks to provide audio. In this case, you can take advantage of the built-in FM transmitter in the tuner box which will broadcast the audio to your car radio instead. You may chose to use just the car radio antenna, just the diversity antenna system, or both. You may or may not have an additional viewing monitor. Installation IR Interface cable 12 Operating your system in a safe and legal manner When operating a motor vehicle, it should always be your highest priority to maintain safe driving habits. It is illegal in many areas of the country to drive with the TV or monitor turned on, when it is visible to the driver. Please check your local and state laws governing the use of Mobile Entertainment systems in your use area. If you have installed the monitor in a position where it is visible to the driver, be sure to install the Safety Cord (included with this system). Wire the cord to an Accessory wire which has + 12V power when the ignition is switched on. The will Prevent the operation of the TV or monitor when the ignition is on. If you do not know how to install this Safety Cord, please consult with a mobile video installer in your area and have it done properly prior to using the system. Using the diversity antennas To attach firmly to your car's exterior. These magnets have a rubber coating to permit secure mounting without risk of damaging your car's finish. [. . . ] Press and hole the POWER On/Off button on the remote until the green LED on the front of the monitor is illuminated. The On Screen Display will show the position of the system at the time it was last turned off (for example, if you were watching CATV Channel 38 when you last turned the power off, the system will display "CATV CH 38"). Turn off the system by pressing the POWER On/Off button on the remote. The screen will go dark and the green LED will go out; the tuner unit will be in STANDBY mode. TV/CATV TV/AV MUTE POWER 1 5 9 VOL 2 6 0 CH 3 7 FM/AM 4 8 SETUP Monitor + - UP FUNC DN MODE Selecting the input Mode Your Video Tuner can switch between four different video sources using the remote control. [. . . ]