User manual PYLE PLVHR85M

[. . . ] Press the mute button from the wireless remote. (TIP: refer to page 4 for the "control & layout") Good picture, but no sound Dolled lines or stripes No picture, or no sound when you connect the optional equipment No response when pressing the buttons on the wireless remote 2 This maybe caused by local interference such as car engine or motorcycle. The wireless remote batteries may be exhausted. Precautions Please read this manual completely and carefully prior to attempt to install your new car video equipment. Install correctly, your new equipment will provide you with years of enjoyable and safe usage. This unit should be installed by a qualified technician or service personnel. [. . . ] Avoid dropping any metal objects or inflammable items into the monitor ventilation slots. After the monitor is installed, do not arbitrarily pull it down or strike it. Do not install this unit where: a) it will obstruct the driver's view. c) it will obstruct the operation of the vehicle, especially the steering wheel, shift lever, or brake pedal. d) a diver or passengers may injure themselves when getting into or out of the car. 3 Control and layout for the monitor Front Audio Output Front audio output (headphones) Front A/V Input Front audio video input Power Cord (Male) Adjust Decrease This multipurpose button serves to decrease the selected parameters, such as volume, contrast etc. Blue screen when no video signal Remote Sensor Remote control IR sensor Power On / Off Turn on/off the monitor Menu Press to display MENU with functions and setting Adjust Increase This multipurpose button serves to increase the selected parameters, such as volume, contrast etc. Notice: some functions are work by remote control. Control and layout for the remote control Power On/Off Turn On / Off the monitor Mute Press to Mute the sound, press again to restore the previous volume level Volume Increase Adjust increase headphone output volume Adjust Decrease This multipurpose button serves to adjust up to select menu function and decrease the selected parameters such as contrast, color, brightness etc. Preset Picture preset by factory V1/V2 Select Video 1 or Video 2 Input Adjust Increase This multipurpose button serves to adjust down to select menu function and increase the selected parameters such as contrast, color, brightness etc Volume Reduce Adjust reduce headphone output volume Menu This button brings up the on-screen menu for adjustment of a range of monitor parameters such as, vol, con, col, bri, tint. Etc Invert To adjust the picture up/down 4 AURM-10B When you use a wireless radio or portable telephone near this unit, picture or sound interference may occur. Do not use such devices near this unit. Accessories Headrest & Sun Visor Shroud Universal Stand AURM-10B Remote Control Headrest Case Key-for removing the monitor from headrest or visor shroud Extension Min Din Cable 7" Wide LCD Monitor With 3 Mounting Options PLHR71 AURM-10B PLVHR85M IN ST RU CT IO N MA NUAL www. pyl eau dio . co m Instruction Manual 5 Connection Diagram 1 2 Fuse (2A) Fuse replacement Never use fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit. When replacing the fuse, be sure to use one that matches the amperage described on the original fuse. If the fuse blows again after replacement, there may be an internal malfunction. Insert the monitor to measure the fit and make adjustment if necessary. 9 Route the cable through the visor Run the supplied cable through the opening and out to the bottom of the visor. Before connecting the monitor, pull the connecting cable assembly through the visor housing as shown in diagram. Place sun-visor shroud into the opening and secure it with correct fasteners. Install the sun-visor shroud Pull the connecting cable through the center of the housing as shown in diagram, and secure the sun-visor shroud with correct fasteners THIS SIDE UP THIS SIDE UP Insert the monitor Push to insert the monitor to the sun-visor shroud. Removal Insert the release key between the monitor and visor shroud gap and pull it out to remove the monitor from headrest shroud. Oper ate your syst em in a saf e and legal manner When oper ate a motor vehi cle, it shoul d always be your highest priority to maintain saf e driving habi ts. It is illegal in many areas of most count ries to drive with TV or MONITOR on, when it is visible to the driver. Please check your local and state laws gover ning the use of MOBILE ENTER TAINMENT SYSTE M in your area. 10 Rear side of headrest Front side of headrest 11 Function setting Press MENU button (1)from the remote or press manual button (1) from the monitor 2 to call out the function menu, press button (2 or 3) to the desired setting. 1 Video Signal Picture Parameters DDP OSD Setup Others 3 OSD Remote Monitor AV1 AV2 Return Press Menu button (1) to enter video signal input selection. The symbol show current video input. 2 1 SEL. MU ENT. EXIT EXIT Remote 3 Monitor Video Signal Picture Parameters DDP OSD Setup Others OSD Press the button( 2or3) to move the symbol and choose video signal input. Preset: 50] Hue 50 2 1 -/+ MU EXIT SAVE / EXIT Remote 3 14 Monitor Video Signal Picture Parameters DDP OSD Setup Others OSD Press the button( 2or3) to adjust the symbol to choose "letter box". The symbol show current selection. [An image with an aspect ratio of 4:3 (regular picture)] Scaling Full Screen Letter Box Paranoma Return 2 1 SEL. MU SET. EXIT RET Remote 3 Monitor Video Signal Picture Parameters DDP OSD Setup Others OSD Press the button( 2or3) to adjust the symbol to choose "paranromal". The symbol show current selection. [An image with an aspect ratio of 4:3, with only the left and right sides of the image being enlarged to fill the screen] Scaling Full Screen Letter Box Paranoma Return 2 1 SEL. Video Signal MU SET. DDP EXIT RET Remote Others 3 Monitor Picture Parameters OSD Setup OSD Press Menu button (1) to enter picture clearness setting. [. . . ] Move the symbol to "RETURN" and press menu button (1) to exit. [Set disable as normal picture] Enable Disable Return 2 1 SEL. Video Signal MU ADJ. DDP EXIT RET Remote Others 3 Monitor Picture Parameters OSD Setup OSD Press Menu button (1) to set the OSD. Language Select OSD Timeout Transparency Information Memory Recall Return 2 1 EXIT SEL. MU ADJ. RET Remote 3 18 Monitor Video Signal Picture Parameters DDP OSD Setup Others OSD Language Select OSD Timeout Transparency Information Memory Recall Return Press the button( 2or3) to adjust the symbol to choose "language". Press menu button (1) to enter language setting. [Setting On Screen Display language] 2 1 EXIT SEL. MU ADJ. RET Remote 3 Monitor Video Signal Picture Parameters DDP OSD Setup Others OSD Press the button( 2or3) to adjust the symbol to desired language (English). Move the symbol to "RETURN" and press menu button (1) to exit. [Set disable as normal picture] Language Select English Exit 2 1 SEL. Video Signal MU SET. DDP EXIT RET Remote Others 3 Monitor Picture Parameters OSD Setup OSD Press Menu button (1) to set OSD appear timing. Language Select OSD Timeout Transparency Information Memory Recall Return 2 1 EXIT SEL. MU ADJ. RET Remote 3 19 Monitor Video Signal Picture Parameters DDP OSD Setup Others OSD Press button 2: increase OSD timeout. Preset:30 seconds] OSD Timeout 30 2 15 1 3 Remote -/+ Video Signal MU EXIT SAVE / EXIT OSD Setup Others Monitor Picture Parameters DDP OSD Press the button( 2or3) to adjust the symbol to choose "transparency" setting. [. . . ]