User manual PYLE PLVHR72 INSTRUCTION MANUAL

[. . . ] RISK OF ELECTRIC SHOCK DO NOT OPEN ! This symbol is intended to alert the user to thepresence of uninsulated "DANGEROUS VOLTAGE" within the product's encloseure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Caution: To reduce th risk of electric shock Do not remove cover (or Back) No user-serviceable parts inside Refer servicing to qualified service personnel ! This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance. Troubleshooting guide The following checklist will help you solve problems you may encounter with your unit. Before going through the checklist below, check the connection and operating. if you can not solve the problem with follows guide, please contact your nearest dealer. Problem No picture, no sound Cause/solution The power cord or battery has been disconnected. Press the volume increase button on the wireless remote, or on the monitor. [. . . ] 2)Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries, battery may be explode PULL OUT if mistreated. PUSH IN 3)Battery replacement is necessary when remote control acts sporadically or stops operating. 7)Do not use remote control for the other equipments at the same time. 8)Do not leave the remote near any heat sources, or in a place subject to direct sunlight (especially on the dashboard). 10)If the MONITOR does not operate even when you operate the remote control from a close range, it is time to replace the battery (use CR-2025 lithium battery), refer ring to the label on the back of the basic control. 11)Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. 6 Steps For Installing Headrest with Shroud Setup work Remove the headrest and set it in an uncluttered work area. Pay the appropriate precautions to ensure that it is not damaged during the installation. CAUTION: make sure the screws are not long enough to go through the headrest!If you have any doubts about this type of installation, please consult your local mobile electronics retailer. Cutting and making holes in the headrest will cause electronic damage which is expensive to repair. Measurements Press the headrest with your fingers to make sure there are no obstructions that would hinder the installation. Use paper template to mark the area to be cut. Cut the headrest Use an adjustable-depth blade, start your cut 1/4 inch inside one corner and cut diagonally across, stopping 1/4 inch in from the other corner. Repeat this procedure for the other two corners. Remove foam & obstructions Carefully peel off the material. Set the adjustable blade to one inch depth and cut around the edges of the hole, staying 1/4 inch inside the edge. Insert the monitor to measure the fit and make adjustment if necessary 7 Route the cable through the headrest Run the supplied cable through the opening and out to the bottom of the headrest. Before connecting the monitor, pull the connecting cable through the headrest shroud as shown in diagram. Place the headrest housing into the opening and secure with correct fasteners. Install the headrest shroud Pull the connecting cable through the center of the shroud as shown in diagram, and secure the headrest shroud with correct fasteners Insert the monitor Push to insert the monitor to the headrest shroud. Removal Insert the release key between the monitor and headrest shroud gap and pull it out to remove the monitor from headrest shroud. 8 Steps For Installing Sun-visor with Shroud Setup work Remove the visor and set it in an uncluttered work area. Pay appropriate precautions to ensure that it is not damaged during the installation. CAUTION: make sure the screws are not long enough to go through the visor!If you have any doubts about this type of installation, please consult your local mobile electronics retailer. Cutting and making holes in the visor will cause electronic damage which is expensive to repair. Measurements Press push on the headliner with your fingers to make sure there are no obstructions that would hinder the installation. Use paper template to mark the area to be cut. Cut the visor Use an adjustable-depth blade, start your cut 1/4 inch inside one corner and cut diagonally across, stopping 1/4 inch in from the other corner. Repeat this procedure for the other two corners. Remove foam & obstructions Carefully peel off the material. [. . . ] Press menu button (1) to enter OSD transparency setting. [Transparency: makes solid or transparency OSD display] Language Select OSD Timeout Transparency Information Memory Recall Return 2 1 EXIT SEL. Video Signal MU ADJ. DDP RET Remote Others 3 Monitor Picture Parameters OSD Setup OSD Press button 2: set increase transparency. Move the symbol to "RETURN" and press menu button (1) to exit. Preset:0] Transparency 2 1 -/+ MU EXIT SAVE / EXIT Remote 3 20 Monitor Video Signal Picture Parameters DDP OSD Setup Others OSD Language Select OSD Timeout Transparency Information Memory Recall Return Press the button( 2or3) to adjust the symbol to choose "information". Press menu button (1) to enter information. [Appear video input information] 2 1 EXIT SEL. Video Signal MU ADJ. DDP RET Remote Others 3 Monitor Picture Parameters OSD Setup OSD Show video signal input information. [. . . ]