User manual PYLE PLTVRD10

[. . . ] Then slide the sleeve off the back of the unit. 30 Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration. DIN FRONT/REAR-MOUNT This unit be can properly installed either from "Front"(conventional DIN Front-mount) or "Rear"(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods. 4 INSTALLATION Sleeve L Key Outer Trim Ring (Tapping Screw (5x25mm) and Plain Washer) to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical grounding of the unit. R Key Spring Washer Hex Nut 5. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. [. . . ] You can point the remote control handset to IR (10) (when the monitor doesn't stretch out) or IR (26) (when the monitor stretches out) and press function keys on the remote control to control the TV unit. The unit is also connected to an external remote receiver (See the electrical connection diagrams on Page 7), and the function is the same with IR (10) and (26). Notes: The external remote receiver is placed near the monitor for the best to receiver remote signal easily. If the angle of the monitor from vertical exceeds 20 (Especially the distance exceeds 3m. ), controlling the TV through IR (10) or (26) cannot get good effect. LIQUID CRYSTAL DISPLAY The LCD (4) can show the current state of the unit. 6. 5 inch TFT DISPLAY When the monitor stretches out, the 6. 5 inch color TFT display (5) can show the current state of the unit. RESET FUNCTION Reset button (9) must be activated with either a ballpoint pen or thin metal object. The reset button is to be activated for the following reasons: Initial installation of the unit when all wiring is completed. Note: When the monitor stretches out and on the central viewing position, activate the reset button (9), the monitor will turn downward and draw in automatically. OPERATING WHEN THE MONITOR NOT STRETCHING OUT When the monitor doesn't stretch out, the front panel of the unit is in state A (see Fig. A), you can operate the unit following the instructions below. Sound mode selection Press SEL button (6) on the front panel or MENU button (45) on the remote control to enter sound mode then pres sTUNING / buttons (13&14) or TUN/CH / buttons (46) to switch between volume, bass, treble, balance, fader, loud and equalization mode. - Program scanning Press AS/PS button (48) shortly to scan preset station. When the field strength level is more than the threshold level of stop level. The radio is holding at that preset number for several seconds with release mute, then searches again. Local/distant Press LOC button (38) on remote control to select between local and distant stations. Local setting for reception of strong station, and a distant setting for reception of weaker stations. Mono/stereo Press MO/ST button (16) on the front panel or ST/MO button (53) on remote control to select mono or stereo mode. You can sometimes improve reception of distant stations by selecting mono operation. Scan Press -/-- (SCAN) button (39) on remote control to set the function to scan mode, which scanning to higher frequency station with receivable 13 OPERATION OPERATING WHEN THE MONITOR STRETCHING OUT When the monitor stretches out, the front panel of the unit is in state B (see Fig. B), you can operate the unit by using the current menu displayed on the 6. 5 inch color TFT display (5). And if the unit is connected to other TV unit through the cable with the 13-pin din plug on each terminal, there have radio mode, TV mode and CDC mode to be selected. When the unit isn't connected to other TV unit through the cable, there have radio mode, AV mode and CDC mode to be selected. The other operations are the same with the operation when the front panel in state A and those will not be described below, you can refer to the above details. [. . . ] (For the unit with NTSC system): COLOR BRIGHT CONTRAST TINT SEARCH 40 40 40 40 Press TUN/CH / buttons (46) to select the item upward or downward. When select SEARCH item, press VOL / buttons (47) to start auto searching then press TUN/CH button on remote control to stop searching. (For the unit with NTSC system): COLOR BRIGHT CONTRAST TINT 40 40 40 40 Volume adjustment Press VOLUME / buttons (23&22) or VOL / buttons (47) to adjust volume level. Screen display Press DSP button (20) on the front panel or DISP button (44) on remote control to display the current status such as TVch /AV1/AV2. [. . . ]