User manual PYLE PLPSE4

[. . . ] HEED WARNINGS---Comply with all warnings on the product and in the operation instructions. GROUNDING or POLARIZATION---This product may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. [. . . ] Selects surround modes: Theater, Hall, Passthru, Movie, Music, and Room. With the unit in the STEREO mode, only front left and front right speakers and Woofer are working. When receiving Analog/digital PCM signal or 2CH Pro Logic, turn on this button then the playing is under analog 5. 1CH state. When playing 5. 1CH source, and while you are enjoying Stereo, push this button to playback source in DTS/DOLBY DIGITAL. It contains one Optical port, one S-video port one video input and Analog Left and Right inputs. When this unit is ON, use a paper clip to press this button for more than 3 seconds to reset the whole system (including memories). Push this button to select inputs Tuner (FM, AM), VIDEO 1, VIDEO 2, VIDEO 3, DVD, AUX, TAPE and PHONO. 10. Push this button to mute the sound, push it again to cancel the mute function. 20. INPUT SELECTOR 11 REMOTE CONTROL INFORMATION 2 3 5 1 4 6 7 9 10 11 TUNING STATION DOLBY DIGITAL POWER MUTE DELAY TIME SPK SETUP 29 28 27 26 25 24 23 21 22 20 19 18 SURROUND MODE BASS MEMORY DOLBY PL II TREBLE INPUT SUBWOOFER ON/OFF SELECT 8 DIMMER CH SELECT DYNAMIC INPUT MODE TEST TONE BAND AUTO/ MANUAL LFE TRIM 12 13 TUNING 14 16 ST/MONO VOLUME 17 P T-6 9 0 A 15 12 REMOTE CONTROL FUNCTION NO. DISPLAY DESCRIPTION Push this button to turn the unit into standby mode, push it again to turn off the unit. Press this button to mute the sound, push again to cancel the mute function. S-VIDEO INPUTS DVD-S IN --- connect to the line output terminal of a DVD player. VIDEO 1-S IN --- connect to the output terminal of a VCR to the VIDEO 1-S IN. ANALOGUE AUDIO IN TAPE IN --- connect to the line output terminals on the TAPE DECK. VIDEO 1 COAXIAL IN --- digital audio input to the digital output of a VCD player. VIDEO 2 OPTICAL IN --- digital audio input to the digital output of a VCD player. FM / AM ANTENNA --- connect to the 7 channels output terminals of another player. (refer to speaker connection diagram) SPEAKERS 8 --- connect to the external speakers. (refer to speaker connection diagram) POWER CORD --- connect to the A/C socket. 14 BASIC OPERATION BASIC OPERATION 1 BASIC OPERATION 2 P OWER MAST ER VOLUME DOLBY DIGITAL/DTS AV RECEIVER PT-690A PO WER ON OF F STANDBY MUTE W OOFER ON/ OFF DIMM ER DIGITAL IN SUR ROUND MODE STEREO PR OLOGIC DTS/ DOLBY DIGITAL OPTICAL S-VIDEO VIDEO L AUDIO R INPUT SELECT OR AV3 IN PHONES A POWER & STANDBY/ON button Press this button to turn the power on. The STANDBY indicator lights up in power standby mode and goes out when this unit is turned on. Select the desired source by pushing corresponding button DVD (ANA, COAX) VIDEO 1 (ANA, COAX. ) VIDEO 2 (ANA, OPT. ) VIDEO 3 (ANA, OPT. ) TUNER (FREQUENCY) TAPE AUX PHONO Note: INPUT MODE is used to select one of the 3 Modes. ANAOPTCOAX With the unit in the STEREO mode, only Front Left and Front Right Speaker and Woofer have output. the C PRO LOGIC II Opposed to Dolby Pro logic, which had four channels (front, left, center, and surround) recorded into two channels with matrix processing and then played back in four channels, Dolby Pro Logic II uses a feedback logic circuit to have 5. 1-channel surround audio(Dolby Surround, etc. ) matrix-encoded into two channels and then played back in its original 5. 1-channel form. There are five standard modes: Movie, Music, Virtual, Pro Logic Emulation, and Matrix. [. . . ] The level of each speaker can be adjusted in 1 dB step from ­10 dB to +10 dB. When the setting is finished, press the TEST TONE button to stop the test tone. Note: You must keep press TEST TONE until one complete cycle is finished. LOW FREQUENCY EFFECT (LFE MIX) LFE (LOW FREQUENCY EFFECT) MIX LEVEL (LFE MIX) Under COAX. /OPT mode, when playing , input AC3 or DTS 5. 1CH signal, LFE will appear on the VFD, then press LFE key on the remote, and again press VOL +/key to adjust the level between 0dB to ­10dB. [. . . ]