User manual PYLE PLHR76 Reference Guide

[. . . ] When mode has not been adjusted for several seconds, display return to normal radio or cd display. and then use vol+/- button to adjust the selected mode as follows: EQ: ESP: MULT: FLAT M CLASS M ROCK M POP M DSP OFF ESP '12 MULT ON ESP '45 MULT OFF WOOFER: BEEP: WOOFER ON BEEP ON WOOFER OFF BEEP OFF D. IN mp3 playback, Used for enter track and file search during MP3 mode after press SEARCH button during track search, after selecting the desired track with 1 digit or 2 digits, selected song begins to play after enter button is pressed for longer than 0. 5 second. During file search, when enter button is pressed or longer than 0. 5second. at the current directory mode, first song in the corresponding director will begin playing. 2 BASIC OPERATION 4. 5. TRACK UP /DOWN BUTTONS A. During RADIO mode, press and hold or for more than 2 seconds you can auto search channel. B. During CD mode, Press or button to choose the following track or the previoustrack. Press and hold or button for several seconds to fast forward or fast reverse. Releasing the button to stop fast playing C. IN MP3 MODE:Press the or button once to choose the next or previous track under normal MP3 playback. 6. [. . . ] MODE BUTTON Press it repeatedly to select CDP, AUX and RADIO mode in sequence and circulation. 7. LUD When reduce volume to half level, press it to enhance the bass effect. 8. ST BUTTON Press ST button to stereo reception for radio stations. 9. OPEN /EJECT Slide it down then you can insert the CD disc into the CD compartment or eject the disc. 10-11-12-13-14-15. To memorize the current frequency, press any one of the six preset Buttons hold for more than 2 seconds. In CDP mode, press 1TOP button to pause CDP playing, press it again to resume CDP playing. In CDP mode, press 2INT button to play the first 10 seconds part of each song, press it again to stop scanning and retain playing the song currently selected. G. In mp3 mode , press the 5-10/6+10 buttton to select back 10 tracks or next 10 tracks. 16. MUTE BUTTON Press it to eliminate the sound immediately. 17. DISP BUTTON Press DSP button immediately to recall time display, then press and hold this button for three seconds until the time is blinking. And press VOL+ button to adjust hour or VOLbutton to adjust minutes. 18. APS/SEARCH BUTTON IN RADIO MODE: When short pressing, the radio searches for each preset station. When the field strength level is more than the threshold level of stop level, the radio is holding at that preset number for few secretary with releasing mute, and than searches again. When long pressing (more than 1 second), the radio searches from the current frequency and checks the signal strength level until 1 cycle search is finished. 5 characters), After entering your song name, press SEL/MENU button more than 1 second to start the search. If no such song, NOT FND will be shown on display. 19. BAND/ID3: During radio mode:Press it to select your desired radio band and the band which is selected will be displayed on LCD. During mp3 mode :Press search button to working Id3 as follow: (depend on the disc used for Mp3) File folder song artist album 20. POWER BUTTON 21. FLASHING LED Press it(more than 1 second) to turn off and short press to turn on the unit. If the front panel is not on the main unit, LED will be flashing. 22. RESET RESET button is placed on the housing and must be activated with either a ballpoint pen or thin metal object. The RESET button is to be activated for the following reasons: -Initial installation of the unit when all wiring is completed. Note: If press RESET button, the unit can't work yet, please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the front panel. 23. LOC When in the radio mode, press it to select local or distance broadcast station receive sensitivity . NOTE: The SCAN button on the remote controller(for RC version only) SCAN BUTTON Press it to scan up by one channel step with station detection. If a valid signal has detected, the current frequency is blinked with in 5 seconds, then press it again to stop scan and remain the current frequency; otherwise, the unit continue to scan up by one channel step with station detection 5 seconds later. 5 ELECTRIC CONNECTION WIRING CONNECTION AUX cable(optional) ANTENNA CONNECTOR RCH RED LCH WHITE IGNITION RED SWITCH(B+) MEMORY(B+) YELLOW GROUND(B-) BLACK AUTO BLUE ANTENNA FRONT FUSE BOX RCA OUTPUT CABLE(optional) RCH RED LCH WHITE FRONT WHITE GREY GREY/BLACK WHITE/BLACK Lch SPK REAR GREEN GREEN/BLACK VIOLET VIOLET/BLACK Rch SPK REAR Lch SPK Rch SPK NOTE: In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the distortion during high volume level. 6 INSTALLATION DASH BOARD HEX NUT METAL MOUNTING STRAP SPRING WASHER PLAIN WASHER TAPPING SCREW CONSOLE SLIDE BRACKET HOUSING HEX BOLT 7 INSTALLATION HOW TO REMOVE AND INSTALL THE FRONT PANEL 1. Press the release button and the right hand side of the front panel will release (FIG. 1) . Pull-off the front panel(FIG. 2) and Keep front panel into the case(FIG. 3). [. . . ] Pull-off the front panel(FIG. 2) and Keep front panel into the case(FIG. 3). To install the front panel, insert the panel into the housing and make sure the panel is properly installed(FIG. 4). otherwise, abnormalities occurs on the display or some keys will not function properly. REMOVING THE FRONT PANEL FRONT PANEL FRONT PANEL RELEASE BUTTON FIG. 1 PROTECTIVE CASE FIG. 2 INSTALLING THE FRONT PANEL FRONT PANEL FIG. 3 FIG. 4 8 NOTES DISC PLAY: CLEANING DISCS Before playing, clean the disc with a clean, lint-free. NOTE 2: Do not try to insert another disc when one has been already inserted. [. . . ]