User manual PYLE PLDVD7M

[. . . ] Use Authorized Service Centres Do not attempt to disassemble or adjust this precision product. Please refer to the Service Centre list included with this product for service assistance. For Installation The unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30°. USE THIS PRODUCT SAFELY When Driving Keep the volume level low enough to be aware of road and traffic conditions. When Car Washing Do not expose the product to water or excessive moisture. [. . . ] MUTE Press and hold ENT/MUT button on the front panel for several secounds or press MUTE button on the remote control to 15 OPERATION RADIO OPERATION SWITCHING TO RADIO MODE Press MOD on the front panel or MODE on the remote control to select radio mode, the radio mode appears in the display together with the memory band and frequency. SELECTING THE FREQUENCY BAND During radio mode, shortly press BND/MEN button on the front panel or BAND (MENU) button on the remote control to select the desired band. The reception band will change in the following order: FM1 FM2 FM3 AM1 AM2 strongest stations are stored into the corresponding preset number button. STATION STORING Press any one of the preset buttons (1 to 6) on the front panel to select a station, which had been stored in the memory. Press this button for several seconds, current station is stored into the number button. MONO/STEREO Press ST/XM-MOD button on the front panal or remote control shortly to select mono or stereo mode. You can sometimes improve reception of distant stations by selecting mono operation. SCAN Press ENT/MUT button on the front panel shortly to set the function to scan mode, which scanning to higher frequency station with receivable signal and keep on each station for several seconds. SELECTING STATION During radio mode, shortly press CH/TUN/TRK button on the front panel or button on remote control to increase frequency by one step of channel spacing, and shortly press CH/TUN/TRK on the front panel or button on remote control to decrease frequency by one step of channel spacing. Hold CH/TUN/TRK / buttons on the front panel longer or press / buttons on the remote control for fast tuning. LOCAL/DISTANT Press ST/XM-MOD button on the front panal or remote control for several seconds to select between local and distant stations. Local setting for reception of strong station, and a distant setting for reception of weaker stations. In direct mode, display shows DIRECT and "000" channel number. (Hundred Digit flashing on/off) 17 FOR VCD/CD: Normal Playback 1X 2X 3X 4X SKIPPING TRACK Press CH/TUN/TRK / buttons on the front panel or / buttons on the remote control during playback. Note: For some VCD 2. 0 dics (PBC-playback control), / or / buttons may be unavailable. SLOW MOTION PLAY Press / button on the remote control OPERATION during play. Each timEach time the button is pressed, the speed of slow changes according to the according to the disc as follow. FOR DVD: Normal Playback 2X 4X 8X FOR VCD: Normal Playback 1X 2X 3X REPEATING PLAYING A PASSAGE A-B repeat allows a passage to be repeated continuously. Press A-B button on the remote control at the start of the required passage, then press A-B button again at the end of the passage. Each time the button is pressed, the screen will display as follows: A TO B SET A A TO B SET B A TO B CANCELLED TIME SEARCH (GOTO) FOR DVD Press GOTO button on the remote control twice, the screen will display the following message: TITLE 01/01 TIME -- : -- : -- PAUSE PLAYING Pressing on the remote control or on the front panel during playback will stop play temporary. REPEATING PLAYING FOR DVD: Press RPT button on the front panel or REPEAT button on the remote control to select repeat mode as follow: CHAPTER REPEAT ON TITLE REPEAT ON REPEAT OFF 00:00:25 FOR VCD/CD: In stop mode, press RPT button or REPEAT button to select repeat mode as follow: REP-ONE REP-ALL REPEAT OFF You can select the item you want to watch through TIME setting by using numeric buttons and ENT/MUT button on the front panel or OK button on the remote control. FOR CD/VCD (WITH PBC OFF): Press GOTO button once, the screen will display the following message: GOTO -- : -00:00:25 1. Continuously repeat at the current chapter/track, when selected REPONE mode. [. . . ] Type the old password (The initial factory code is 3308) and key in 4 characters password now you want to use, and retype again to confirm key in correctly. 27 SETUP --- PREFERENCES PAGE --TV TYPE AUDIO SUBTITLE DISC MENU PARENTAL PASSWORD DEFAULTS SMART NAV LOGO MAIN PAGE RESET --- PREFERENCES PAGE --TV TYPE AUDIO SUBTITLE DISC MENU PARENTAL PASSWORD DEFAULTS SMART NAV LOGO MAIN PAGE ORIG LOGO CUST LOGO DEFAULTS Select reset to revert to factory initial settings. --- PREFERENCES PAGE --TV TYPE AUDIO SUBTITLE DISC MENU PARENTAL PASSWORD DEFAULTS SMART NAV LOGO MAIN PAGE NO MENU WITH MENU LOGO Select ORIG LOGO (original picture when the unit turns on) or CUSTLOGO (customer-set picture when the unit turns on). Load the picture disc into the drive of the DVD unit, when you select the desired picture, press button then press TITLE button, the current picture will be stored in the unit and "LOGO IS COPIED" will appear on the screen. SMART NAV If selected WITH MENU mode, when playing an MP3 disc, the smart navigation menu will appear on the screen, then the user can select a track to play according to the menu hint. If selected NO MENU mode, when playing an MP3 disc, there is no menu to display and it starts to play directly. [. . . ]