User manual PYLE PLDF7IN

[. . . ] Professional radar distance test module can be used alternatively, which makes the monitoring and entertainment be done at the same time and frees you of apprehensions in the rear. Wide band voltage design is applicable to the requirements of all types of automobiles. In order to correctly install and use this product, please read this manual attentively. Characteristics 2. 1 Specifications 2. 1. 1 System parameters Items Voltage Current Working Temp. Video system Inputs Sizes Parameters DC 11V-14V 1. 5A Amplifier off MAX 10 -10 60 -30 80 Auto PAL or NTSC One channels of video input/backing lens input (Comprise one channel of back running video) 178(W) 176(L) 100(H) mm -1- Weight Screen size Resolution Dot pitch 2. 6 kg 16:9 6. 5 inches diagonal 1200 234 pixels 0. 136(H) 0. 416(V) 2. 1. 2 Performance parameters Items Parameters FM/AM modulation parameters FM:87. 5-108MHz AM:522 1611Mhz Modulation Display Memory capacity Seeking Phase-locked loop frequency modulation Panel LCD or OSD FM:16 AM:8 Automatic/by hand TV parameters VHF-L 48. 25 Band Receive System Seeking Memory method Memory capacity Antenna resistance Voltage Current Audio output Vol. [. . . ] (18) to select LCD screen setup, press (18) vertically to confirm into LCD screen BRIGHT :32 COLOUR:22 CONTR :25 ANGLE :30 VIEW :WIDE 5. 3. 2 Balance adjustment up and down, right and left. Press SET to enter into menu setup, press or (18) to select Balance Adjustment Up &Down, Right & Left. press (18) vertically to confirm entering into Balance Adjustment Up &Down, Right & Left. Press (18) respectively + will Rear L BALANCE Rear R Front L Front R move up and down, right and left to control the volume of the four channels up and down, right and left. Press SET again to exit system setup + is in the 5. 3. 3 System setup Press SET to enter into system setup. Press or (18) to select System Setup, press SYS SETUP BLUE :ON BEE :ON BACK:ON TIME :ON TIME :ADJ OFF OFF OFF OFF (18) vertically to confirm entering into system setup mode. The blue screen, beep, car-backing, view switch, time displaying and time adjustment can be set up respectively. Press or (18) to select up and down, and the selected menu will become pink; press Or (18) to make setup. Press SET again to exit System When the blue screen is set to ON , and no visual signal is input, the screen will display in blue. Note: 5. 4 Time setting Press SET to go into System Setup (refer to 5. 3. 3 in detail), and select TIME ADJ, press right picture. Press or (18) for time adjusting, press or (18) for change-over selection between HOUR and MINUTE. vertically after that to confirm and store the time setup, (18) vertically to confirm entering into time setup mode. The screen will display as the TIME ADJ 12:00 5. 5 Monitor angle adjust When the system is ON , short pressing can adjust the display angle to the preset angle or return to vertical mode. Push forward the plates into box until you hear a sound of click. To avoid accidental failure, place only one disc on one plate. 9. 6. 2 Remove discs Draw out disc plates out of CD changer to stop position, take out of discs with hands. Take CD changer with care, if the disc insertion position faces downward, there may be a risk of slipping disc out of plates. 9. 6. 3 Insert disc box Glide the door leftward until the door is opened widely with a sound of click. Check equipment top and the direction of disc insertion, push CD changer inside gently until a sound of click. Close door until you hear a sound of click. Make sure to close CD changer door closely to prevent dusty enter. 9. 6. 4 Remove disc box Screw ignition key turn on receiver power. Draw out CD changer according to arrow direction, until CD changer glides out of equipment. CAUTION: If in any case, the CD changer can not be draw out, press RESET button and push the CD changer inside with strength, then press ejection button . , AV operation 10. 1 AV play Press AV button, start playing A V select other function(TV Radio DVD CDC), stop playing AV. Note: The AV input channel is commonly used with car-backing scene, if you use AV function, please set the BACK in Sys Setup to OFF (refer to 5. 3. 3 in detail) . 10. 2 Backing with backsight If you want to use the rear-view function at backing, please set BACK in Sys Setup to ON (refer to 5. 3. 3 in detail). When the car converters into BACK, no matter what condition the system is in, it will automatically transfer to back view display, the screen will display will restore automatically. After leaving the BACK mode, all the functions of the system , Necessary Disc machine installation In Example of Panasonic DP88 11. 1 Appearance 11. 1. 1 CD changer AH C V Door Reset Compact disc area Eject Angel Adjust Screw There are two angel adjust screws for both sides. 11. 1. 2 Compact disc and tray Compact disc inserting direction B Tray D IG CAUTION Do not use a disc with 8cm diameter. Tray should be placed in the right position before inserting compact disc. D ii s Ds ITA A LA UD D c CO IO MP M AC T 11. 2 Installation guidance 11. 2. 1 Installation location When the temperature in car is too high, do not install this instrument on rear undercarriage to avoid the problems, in case it is caused by the contact with it. The following locations also should be avoided, Direct sunshine hot air from heater or other high temperature places. Too much humid, dirty or dusty. 11. 2. 2 Installation work According to your selected installation angle, use a screwdriver to adjust the angle-adjustment screw to a position of V or H When set to vertical position Choose V position. This equipment has 5 positions for your choice A)Horizontal b) Vertical c) A 22. 5 degrees d) B 45 degrees e) C 67. 5 degrees The following data is for your reference in installation. H A B Angel Adjust Screw C V 11. 2. 3 Installation angle Horizontal installation The instrument should be placed as follows. <10 degrees AH C V B H A <10 degrees B V Incline angle is less than 10 degrees. (As shown in top figure. ) Place screws in same positions in both sides (as shown in left figure). C C -18- Vertical installation Vertical installation as shown below Incline angel <10 degrees (as shown below) Place screws in same positions in both sides (as shown below) <10 degrees A B C V H 11. 2. 4 Typical horizontal installation Use a hexagonal bolt with 2 washers(M4 8mm) Fix left and right installation trays onto host instrument. Right tray AH C V Left tray Hexagonal bolt with 2 washers(M4 8mm) 4 -19- B Choose position to install fix trays with double sided adhesive tape. AH C B V Double sided adhesive tape 2 Tray 2 Cut a small cross on carpet in the position, which is right towards the M5 bolt on tray. Carpet Tray 2 Fix both tray and tape onto installation plate under carpet. -20- Use 4 hexagonal bolts(M5) to install the equipment onto the 4 holes on carpet. Exagonal bolts(M5) 4 Carpet 11. 2. 5 Typical vertical installation Fix trays onto the both sides of equipment by using hexagonal bolt with 2 washers (M4 8mm) Left tray Right tray Hexagonal bolt with 2 washers(M4 8mm) 4 C C V V BB AH AH 11. 2. 6 The relations between angles and installation holes. H A H H B C V A B V C C V C B A V B H A Left tray Right tray The above figure has explained clearly the relation between installation holes and installation tray (left and right) angles. [. . . ] Please turn off the power supply first when you plan to clean the machine. The product is specially designed for vehicle, which is equipped with a 12V -25- 13. 2 Precautions on CD Dirt, dust, scratching and bended disc will result in operation error. The disc should not be placed at the following places The places in straight sun shine. Clearing discs Use the wet soft cloth to scrub the surface of the disc. [. . . ]