User manual PYLE PLCDUSB88MP3

[. . . ] Good ground connections eliminate most electrical noise problem and require tight with the metal vehicle chassis. remove plastic, paint or dust for good electrical contact. SPEAKER WIRING The unit is only designed for the use with 4 speakers system, it can only be connected with speakers rated in the load impedance range from 4 to 8 ohms. Never combine (BRIDGE) the outputs for use with 2 speakers, and Never ground any Negative speaker to the chassis ground. CAR ANTENNA Subwoof RED WHITE RCH LCH CAR ANTENNA RED WHITE RCH LCH RCA line out Auxin RED WHITE RCH LCH RCA line out Connect to control for antenna or remote control for amplifier. Orange Memory+ Connect to battery or +12 volts of power source that is always live. YELLOW Green Green /white Grey Grey /white Right Front Blue Blue /white Right Rear Ground- Black Left Front Brown 12V+ Connect to lgnition key switch. Red Brown /white Left Rear 3 Before installing the receiver permanently, fit it in the approximate place in your car Connect the equipment according to the speakers and electrical connections. [. . . ] Never combine (BRIDGE) the outputs for use with 2 speakers, and Never ground any Negative speaker to the chassis ground. CAR ANTENNA Subwoof RED WHITE RCH LCH CAR ANTENNA RED WHITE RCH LCH RCA line out Auxin RED WHITE RCH LCH RCA line out Connect to control for antenna or remote control for amplifier. Orange Memory+ Connect to battery or +12 volts of power source that is always live. YELLOW Green Green /white Grey Grey /white Right Front Blue Blue /white Right Rear Ground- Black Left Front Brown 12V+ Connect to lgnition key switch. Red Brown /white Left Rear 3 Before installing the receiver permanently, fit it in the approximate place in your car Connect the equipment according to the speakers and electrical connections. When your system is operated properly, (preferably with the car engine running), follow the instructions for permanent installation of your system. 3)Support strap (supplied) INSTALL THE UNIT 1)Install half sleeve, can be with or without adapter. 2)Bend over some tabs where possible tosecure the half sleeve inside of dash. 3) Support strap to bestrutted under dash, secure this strip to avoid skipp ing of disc. 2)Bend over tabs of half sleeve (supplied) 1) Adapter (not supplied) REMOVING THE UNIT Insert removal wrench into the small gap on the right side of the unit and pull the unit slightly out on the same side, then release the wrench. By now, you can remove the unit and unplug the wires connector. Half sleeve (supplied) 4) Two wrenches for release the unit (supplied) 4 Volume POWER ON /OFF VOLUME PWR EJECT Increasing volume VO VO Rotate the [VOL+]button VOL L- L+ Decreasing SEL VOL SEEK Rotate the [VOL-]button MODE SEL SCN DSP RPT SHF BAND CLOCK 1 2 3 4 5 6 SELECT RELEASE DSP CLOCK MODE Eject LOC ST LOUD CH Out LCD display Press the [ In ]button to eject the disc out of the unit . Power Tur ning ON the power Press the [ ]button again, to load the disc in. Press the [PWR]button. EJECT Press to turn on the unit power, Press the button to turn off the unit. 5 Hour MODE Selecting radio and play Press the [MODE]key. Each time you press the key, it`ll switch between radio and CD position. (If mode with AUX IN, the function is below: press MD(MODE)to select: 1 If with DISC, press MD that is: Press [ Minute ] button to set the hour. And 6 powerful stations in this band will be stored into NO. 1-6 respectively. There are 6 bands for selection:FM1, FM2, FM3, AM. Make selection by pressing BAND Button. If with DISC in unit, press [MODE] switch to radio MODE first. Selecting and pressing the buttons stored, you can play the station you want then. 9 Loading and replacing the batter y MUTE POWER SCAN PAUSE SHUF DSP VOL+/CHAR. SEL SEL VWX8 SHIFT MODE PWR -, _, +, 0 MUTE MODE STU7 ENTER LOUD BAND BAND/LOUD REPEAT AS/PS LOCAL MONO ABC PAUSE 1 DEF SCAN 2 GHI RPT 3 6 Use one lithium battery(CR2025) insert the batteries with the +and - poles aligned properly. Following the illustration inside the case. AS/PS ID3 JKL SHF 4 MNO DISC DN CHAR. SEL 5 PQR DISC UP LOC DSP + RO/SN MONO YZ9 SPACE CLK CHAR. SEL - SELECT Pull out Store unused batteries out of the reach of children. Contact a doctor immediately if the battery is accidentally swallowed. Do not set the remote on hot places such as above the dashboard. _, -, +, 0, PWR MUTE S, T, U, , MODE Enter, BAND A, B, C, 1, PAUSE D, E, F, 2, SCAN G, H, I, 3, REPEAT J, K, L, 4, SHUF M. N, O, 5, DISC DN P, Q, R, 6, DISC UP Mode select LOC DSP Char. sel(A, B~8, 9, 0), +/- Basic operation Tur ning ON the power RADIO. SCAN MONO Y, Z, , space, V, W, X, Char. shift, SEL CLK Press the [PWR]button. Press to turn on the unit power, Press the button to turn off the unit. 10 ID3 Press ID3 on remote or Panel enter ID3 selection. one press ID3 enter ID3 file selection mode, F will be indicated on LCD. To read in your desired song name by pressing remote - buttons, then press confirmed the song playing. EXAMPLE: to read in " I LOVE YOU" In the read in mode: press button three times read I, press turn to next word, press three times read L, press three times read O and so on. . . Press / select desired directory, then press confirmed playing. ABC YZ9 ENTER Exter nal view . . . . . . . . [. . . ] To read in your desired song name by pressing remote - buttons, then press confirmed the song playing. EXAMPLE: to read in " I LOVE YOU" In the read in mode: press button three times read I, press turn to next word, press three times read L, press three times read O and so on. . . Press / select desired directory, then press confirmed playing. ABC YZ9 ENTER Exter nal view . . . . . . . . [. . . ]