User manual PYLE PLCDCS200

[. . . ] · AUXILIARY INPUT The unit can be connected to a portable audio player through the AUX IN jack (11). · RESET RESET button (28) must be activated with either a ball point pen or thin metal object. The RESET button (28) is to be activated for the following reasons: - Initial installation of the unit when all wiring is completed. [. . . ] Stations are searched automatically from next frequency and detected station is stored into the preset memory. In case of LOC state, the first Auto Store is done by LOC state and if 6 CH is not fully 7 CASSETTE OPERATION · PROGRAM BUTTON These two buttons (25) perform the dual functions of changing the direction of tape playback and fast forward/rewind of the tape. - Change Tape Playback Direction Press both buttons together to play the other side of a tape. - Fast Forward/Rewind Press the button with the double arrows pointing the same direction as the direction indicator in the LCD to fast forward; press other button in the opposite direction to fast rewind. · EJECT Push the eject button (24) down to eject the cassette tape. · CASSETTE COMPARTMENT Insert a cassette tape into the cassette compartment (26). The cassette mechanism will load it in play mode. OPERATION CDP OPERATION · SELECT TRACKS Press TUNE/TRACK/SKIP button (16) or TUNE/TRACK/SKIP button (17) to move to the previous track or the following track. Hold TUNE/TRACK/SKIP button (16) or TUNE/TRACK/SKIP button (17) to fast reverse or fast forward. · REPEAT THE SAME TRACK Press RPT button (21) to continuously repeat the same track. · PREVIEW ALL TRACKS Press SCN button (20) to play first several seconds of each track on the current disc. · PLAY ALL TRACKS Press RND button (22) to play all tracks on CD in random order. · EJECT When the front panel is folded down, press eject button (4) to stop CD playing and eject the disc from the disc slot (5). REMOTE CONTROL HANDSET 1 7 4 3 8 6 13 12 11 15 9 5 2 10 14 FUNCTION KEYS & CONTROL 1. TUNE/SEEK 10. EQ 11. PRESET 12. PAU 13. SCN 14. RPT 15. RND = = = = = = = = = = = = = = = Power Button Mute Button Select Button Volume Up Button Volume Down Button Band Select Button Mode Button Tune/Seek Down Button Tune/Seek Up Button Preset Equalization Button Preset Buttons Pause Button Scanning Button Repeat Button Random Button 8 SPECIFICATIONS GENERAL Power Supply Requirements Chassis Dimensions Loading Impedance Maximum Output Power Current Drain : : : : : DC 12 Volts, Negative Ground 200 mm (W) x 138 mm (D) x 75 mm (H) 4 - 8 per channel 4 x 50 Watts 10 Ampere (max. ) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 55 dB : More than 50 dB : 20 Hz - 20 KHz CASSETTE PLAYER Tape Speed Fast Forward Time Frequency Response Channel Separation Crosstalk Wow and Flutter : : : : : : 4. 76 cm/sec 180 seconds (C-60 type) 50 to 8, 000 Hz > 35 dB > 40 dB 0. 35% WRMS RADIO Frequency Coverage I. F. Sensitivity (S/N = 30 dB) Image Rejection Stereo Separation Frequency Coverage I. F. Sensitivity (S/N = 20 dB) : : : : : FM 87. 5 to 107. 9 MHz 10. 7 MHz 3 µV > 45 dB > 30 dB AM : 530 to 1710 KHz : 10. 71 MHz : 32 dBu 9 TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Solution If the power supply is properly connected to the car accessory circuits, but the engine is not moving, switch the ignition key to "ACC". Disc cannot be loaded or ejected. Presence of CD disc inside Remove the disc in the player, then the player. [. . . ] (Most vehicles employ this wire and resistor but it may be necessary to check them for correct operation. ) Another method of suppression is the use of additional noise suppressors. These can be obtained from most CB/Amateur radio or electronic supply shops. Interference Radio reception in a moving environment (automobile) is very different from reception in a stationary (home). AM reception will deteriorate when passing through a tunnel or when passing under high voltage lines. [. . . ]