User manual PYLE PDCD4000

[. . . ] ·Do not attempt to clean the unit with chemical solvents as this might damage the finish. ·Keep this manual in a safe place for future reference. SAFETY CERTIFICATION Laser Diode Properties Material: Ga-AI-As Wavelength:755-815nm(25oC) Laser Output: Continuous Wave max. 0. 5mW CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. 2 DESCRIPTION OF THE FUNCTIONS Function of the Main Unit: 1. Pressing the disc tray OPEN/CLOSE buttons will open or close the tray. 3. OPEN/CLOSE(Disc Tray Open/Close Button) Press to load or eject the disc. [. . . ] 4. AC INPUT Connect the supplied power cord into an AC wall outlet with the proper AC voltage. 5. LINE OUT(Output Jacks) The audio from each CD player is output from these jacks. Connect to the line input of the mixer 6. CONNECTOR PORTS The 9-pin termination permit the connection of the main unit to the control unit. 3 Function of the Control Unit UNIT:mm 1. UNIT 1-Control Operation Panel This operation panel remotely controls the main unit 1. Unit 2-Control Operation Panel This operation panel remotely controls the main unit 2 3. OPEN/CLOSE(Disc Tray OPEN/CLOSE Tray) Press to load or eject the disc. LCD These liquid crystal displays (LCD) indicate the track numbers, time (minutes, seconds, frames), etc. PLAY/PAUSE(Play/Pause Button) Each press of the PLAY/PAUSE button cause the operation to change from play to pause or pause to play. JOG DIAL(+FWD&-REV) *Speed Control Rotating this dial in play mode will change playback speed accordingly. Rotate clockwise, the player speeds up; rotate counter-clockwise, the playback slows down. Use of another cable might cause damage. 6 BASIC OPERATION Loading and Ejecting the Disc Open the tray When the disc tray is closed, press the OPEN/CLOSE button to open the disc tray(This may be done on either the player or the remote control side. ) Place a disc in the disc tray Press the OPEN/CLOSE button to close the disc tray. The disc tray will close and the preparation for disc play will begin. When preparation is completed, the total tracks number & total playing time will display. To the desired track 7 TRACK SKIP To go back through the tracks To advance through the tracks Tracks change as follows This is for a disc containing 4 tracks Tracks change as follows When this button is pressed once , the CD player will When this button is pressed once, the CD player will skip backward to the beginning of the track. will skip backward to the previous track. Operation of Play, Pause and CUE 1. Press the PLAY/PAUSE button to switch the operation between PLAY and PAUSE. The indicator LED is illuminated during play, and blinking when in pause. When CUE LED is illuminated and in Play mode, pressing the CUE button goes back to the memorized point and is in pause mode. If a cue point is not memorized, pressing the CUE button will return back to the beginning of the track. 8 SEARCHING ·Scanning is used to accurately locate the point where you wish to start. ·Dial the jog while in Pause mode to search forward or backward. ·Dial the jog clockwise to search forward, dial counter-clockwise to search backward. SPEED CONTROL ·Speed control is used to change the bass beats of playback. ·Dial the jog while in Play mode to raise or lower the playback speed. ·Dial the jog clockwise to raise the speed, counter-clockwise to reduce it. MATCHING THE BEATS PER MINUTE Match the pitch by monitoring the music of both UNIT 1 and UNIT 2 by ear. [. . . ] When the tempo of the music of the 9 selected CD player is slow compared to the tempo of the other player, move the slider to the + side and match the tempo. The following example is for matching the pitch of UNIT 2 to the pitch of the music being played on UNIT 1. UNIT 1 is playing. Press PLAY/PAUSE to start UNIT 2. Listen to UNIT 2 in your headphones. When UNIT 2 is slow compared to UNIT 1 When UNIT 2 is fast compared to UNIT 1 Beat Matching Using Pitch Bend A description of the procedure for matching the beat of UNIT 1 and UNIT 2 using the PITCH BEND stick is given below. This example is for matching the beat of UNIT 2 to the beat of the music being player on UNIT 1. (This procedure can be done on either Unit. ) After Matching the BPM's BPM (Beat Per Minute) is the same, however the bass beats are not matched. When UNIT 2 is ahead. When UNIT 2 is behead. BEFORE SWITCHING OFF THE POWER When you have finished using the CD player, before switching off the power be sure that the disc tray has 10 been closed with the OPEN/CLOSE button. Do not switch off the power when the disc holder is open. [. . . ]