User manual PROMISE ULTRA66

[. . . ] Ultra66 User's Manual Version 1. 0 Ultra66 Copyright Copyright by Promise Technology, Inc. No part of this manual may be reproduced or transmitted in any form without the expressed written permission of Promise. Promise is not liable for any errors contained herein, or incidental or consequential damages in connection with furnishing this material. The published information in the manual is subject to change without notice. [. . . ] ¡ Insert the "Ultra66 Driver" diskette into the A: drive. A message informing you that Windows has found "Promise Technology, Inc. , Ultra66 IDE Controller" should appear. £ Press "Next, " then "Finish, " then "Yes" when asked if you want to restart your computer. Be sure to remove the diskette from drive A:. Installing Drivers with Existing Windows 95/98 The following three sections detail the installation of Ultra66 drivers on a system that has Windows 95/98 already installed. If you're installing the Ultra66 drivers on a system during a Windows 95/98 installation, see "Installing Drivers During Windows 95/98 Installation" on page 6. Windows 95 4. 00. 950/4. 00. 950A 1 After installing the Ultra66 controller card and configuring the hard drives (see "Hardware Installation" on page 4), power up the system and boot Windows. 2 The "Add New Hardware Wizard" will appear, informing you that 8 PROMISE TECHNOLOGY, INC. Section 3 it has found a "PCI Mass Storage Controller. " 3 Insert the "Ultra66 Driver"diskette in drive A:. Choose the "Device Manager" tab, and then click the "+" in front of "SCSI controllers. " "Promise Technology, Inc. , ULTRA66 IDE controller" should appear. Windows NT If you're installing Ultra66 under Windows NT 3. 51, create a floppy disk titled "Windows NT 3. 51 Ultra66 Drivers. " Copy the following files onto the root directory of the diskette: "TXTSETUP. OEM" and "OEMSETUP. INF" from the "NT351" directory of the "Ultra66 Driver" diskette; and "ULTRA66. SYS" and "DISK1" from the root directory of the "Ultra66 Driver" diskette. When prompted for drivers during the installation of Windows 3. 51, insert this diskette in drive A:. Under Windows 4. 0, insert the "Ultra66 Driver" diskette in drive A: when prompted for the drivers. Installing Drivers During Windows NT 3. 51/4. 0 Installation 1 Start the system installation by booting from the Windows NT disk: a) Floppy install: boot the system with the Windows NT installation diskettes. b) Floppyless install: boot from floppy and type "WINNT /B". On the reboot, press the "F6" key when the message "Setup is inspect- 10 PROMISE TECHNOLOGY, INC. Section 3 ing your computer's hardware configuration. . . " appears. c) CD-ROM disk install: boot from the CD-ROM disk and press the "F6" key when the message "Setup is inspecting your computer's hardware configuration. . . " appears. When the "Welcome to Setup" window is generated, press "Enter. " In the "Setup Method" dialog box, press "Enter" to confirm "Express Setup. " Press "S" to configure an additional adapter. Select "Other, " and then insert the "Ultra66 Driver" diskette (for Windows NT 4. 0) or the "Windows 3. 51 Ultra66 Drivers" diskette (for Windows NT 3. 51; see "Windows NT" on page 11 for more details) into drive A:. Specify "A:", and then press "Enter. " Follow the normal installation procedure. 2 3 4 5 6 Installing Drivers with Existing Windows NT 3. 51 Hard drives should not be connected to the Ultra66 controller card before performing the following procedure. The Ultra66 drivers must be loaded on the system hard drive (running under the existing hard drive controller) before any hard drives are connected to the Ultra66 controller card. 1 In "Program Manager, " double-click on "Windows NT Setup" in the "Main" group. 2 In "Windows NT Setup, " select "Options, " and then choose "Add/Remove SCSI Adapters. . . " 3 In "SCSI Adapter Setup, " press "Add. . . " 4 In "Select SCSI Adapter Option, " select "Other (requires a disk from a hardware manufacturer)" in the "Adapter:" dialog box. Insert the "Windows NT 3. 51 Ultra66 Drivers" (created from the "Ultra66 Drivers" diskette; see "Windows NT" on page 11 for more details) diskette into drive A: and type "a:\" in the dialog box. Select "Promise PROMISE TECHNOLOGY, INC. 11 Section 3 Technology, Inc. , Ultra66 Controller, " and then press "OK. " 7 The "Select SCSI Adapter Option" will appear. Press "Install. " 8 After successfully installing the driver, the "SCSI Adapter Setup" dialog box will show that the "Promise Technology, Inc. , Ultra66 Controller" has been installed. !Installing Drivers with Existing Windows NT 4. 0 Hard drives should not be connected to the Ultra66 controller card before performing the following procedure. [. . . ] - 5:30 p. m (PST) (408) 425-9163 Attention: Technical Support GO Promise Promise Technology Attention: Technical Support 1460 Koll Circle San Jose, CA 95112 PromiseOnlineTM 24-hour FaxBack document service Technical support (telephone) Technical support (fax) CompuServe Mailing address PROMISE TECHNOLOGY, INC. 17 Appendix C Limited Warranty Promise Technology, Inc. ("Promise"), warrants that for two (2) years from the time of the delivery of the product to the original end user: a) the product will conform to Promise's specifications; b) the product will be free from defects in material and workmanship under normal use and service. This warranty: a) applies only to products which are new and in cartons on the date of purchase; b) is not transferable; c) is valid only when accompanied by a copy of the original receipt. This warranty shall not apply to defects resulting from: a) improper or inadequate maintenance, or unauthorized modification(s), performed by the end user; b) operation outside the environmental specifications for the product; c) accident, misuse, negligence, misapplication, abuse, natural or personal disaster, or maintenance by anyone other than Promise or a Promise-authorized service center. Disclaimer of Other Warranties This warranty covers only parts and labor, and excludes coverage on software items as expressly set forth above. [. . . ]