User manual PRO-JECT RPM 6.1 SB SUPERPACK

[. . . ] Use absorbent kitchen paper to remove any oil or grease from the outer edge of the hub and the belt. Remove the two red transport screws (1) which secure the motor (22) during transportation. Store it together with the two red motor transport screws (1) in the original packaging so they are available for any future transportation. Cartridge downforce adjustment The counterweight (6) supplied is suitable for cartridges weighing between 6 - 10g. Alternative counterweights for cartridges weighing between 10 - 15g, 9 - 11g or 4 - 6g are available as accessory parts. [. . . ] Slacken off the screw just enough to be able to revolve the arm tube without applying force. With the aid of a good magnifying glass adjust the needle until it is vertical in the groove (i. e. Ideally this should correspond to the top surface of the cartridge body being parallel to the record surface. When you are satisfied that the needle is vertical retighten the screw carefully. Under no circumstances should the arm tube be adjusted with the needle still in the record groove!The arm must be lifted to make each adjustment and lowered afterwards to check it. 4 © Audio Trade GmbH · Pro-Ject RPM 6. 1 SB SuperPack / Ort Samba · Revision 1. 3. 08/1. 5. 08 Anti-skating force adjustment The anti-skating force must be adjusted according to the mass of the cartridge as follows: Downforce Groove in the stub (15) 10 - 14mN 1st from bearing rings 15 - 19mN 2nd " " " rd 20mN and bigger 3 " " " Hang the loop of the thread of the anti-skating weight in the groove of the anti-skating stub (15) corresponding to the downforce applied to your cartridge and feed the thread through the loop of the wire support (17). Connection to the amplifier The record player has gold plated female RCA phono sockets (14) so you can substitute the interconnect cables supplied with those of your choice for connection to the amplifier if you wish. Use the Phono input (sometimes labelled gram, disc or RIAA) on your amplifier. Make sure that the phono input offers correct matching and amplification for the type of cartridge used. The right channel is usually marked red, the left channel black or white. Check the manual supplied with your amplifier for relevant information. An earthing wire may be connected to the screw terminal between the sockets if you encounter hum problems when using the record player. If your amplifier does not have an input suitable for phono cartridges you will require a separate phono amplifier stage for MM or MC cartridges such as the PRO-JECT PHONO BOX or the PRO-JECT TUBE BOX which is then connected between the record player and a free line level input of the amplifier. For detailed product information please refer to the Pro-Ject web site www. project-audio. com. The recommended load resistance for the factory fitted cartridge is: >10 ohms /MC-input Mains power connection The turntable is supplied with a power supply suitable for your country's mains supply. Check the label before connecting to ensure compliance with the mains rating in your house. Connect the low voltage plug from the power supply to the socket (13) on the rear of the record player before connecting the power supply to the mains. Switching on and off Pressing the power switch (20) alternately starts or stops the motor. Changing replay speed 33 Speed45/78 33 Speed Box SPEED BOX SPEED 45/78 Press the speed change button (24) to switch between 33 and 45 r. p. m. . The selected speed is shown respectively by the lit green LED (33 r. p. m. ) or red LED (45 r. p. m. ). perform the following steps: Remove the platter (5) and using the tool (3a) from the accessory kit. [. . . ] If you are not well acquainted with the adjustment of cartridges you are advised to call upon the willing help of your PRO-JECT dealer to accomplish this task for you. The finger lift (21) must be fitted on top of the headshell under the cartridge fixing bolts or nuts - not between headshell and cartridge body. Please note: adjusting a cartridge and tonearm calls for the greatest care in order to avoid damaging the cartridge or tonearm bearings. Leave this work to your dealer if you are in any way unsure of the necessary steps and precautions to be taken. Technical specifications PRO-JECT RPM 6. 1 SB * Electronic speed change Speed variance Wow and flutter Signal to noise Downforce range Effective tonearm length Overhang Power consumption Outboard power supply Dimensions (W x H x D) Weight * 33, 33/* 45, 11 and 78 r. p. m. [. . . ]