User manual PRO-JECT DEBUT CARBON PIANO

[. . . ] Never place any naked flame sources, such as lighted candles on or near the device. The product shall not be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions. Keep plastic bags away from children to prevent any risk of suffocation. © Audio Trade GmbH · Pro-Ject Debut Carbon/Phono USB / Ortofon OM10 · Revision 2013. 3. 15 ! 3 Set-up The deck is supplied partially disassembled and carefully packaged for safe transport. Make sure the surface you wish to use the turntable on is level (use a spirit level) before placing the turntable on it. [. . . ] The right channel is usually marked red, the left channel black or white. Check the manual supplied with your amplifier for relevant information. The earthing wire of the tonearm lead should be connected to the earth terminal on your amplifier (if provided). For detailed product information regarding Pro-Ject Audio interconnect cables please refer to the Pro-Ject web site www. project-audio. com. The recommended load impedance for the factory fitted cartridges is: 47kohms /MM-input The 3, 5 mm connector (supplied) can be used to connect your Pro-Ject Debut Carbon/Phono USB to any line level/auxiliary input (Computer, Midi System, Mixer etc. ). Connect the socket end to the phono plugs at the end of the audio trailing lead from your turntable and insert the 3, 5 mm plug into the relevant socket on your audio component. Connecting to a Computer Connect the USB-output of the unit to a free USB-socket on your computer and turn it on/make sure it is powered on. The “new hardware found assistant“ will automatically detect the unit and announces it as a Microphone USB audio codec. For example - Windows 7® operating system:  Control Panel  Sound  Recording  Microphone USB Audio CODEC  Properties  Advanced: set to 2 channel, 16 bit, 48000 Hz (DVD Quality) Please note: Connection should be made to an USB-socket of your computer directly. Connecting to USB-hubs or switches can cause problems. Recording Programme In case you do not have a recording programme installed on your computer, you may download one free from the Internet. In the menu of the recording programme, source or input may have to be set to Microphone USB audio codec. Please be aware that downloads from the Internet are made entirely at your own risk. Under no circumstances can we carry responsibility or provide support for third-party software products sourced from the internet or for any damage or problems arising from the use thereof. All downloads should be checked with an up-to-date anti-virus programme. License fees may be applicable. Mains power connection Connect the mains lead to the mains. voltage in your area meets the voltage requirements printed on a label underneath the unit. Useful tips The record player should be positioned on a low-resonance surface such as wood or multiple layer ply board to avoid structural vibrations disturbing replay. Switching on and off Pressing the power switch (19) alternately starts or stops the motor. © Audio Trade GmbH · Pro-Ject Debut Carbon/Phono USB / Ortofon OM10 · Revision 2013. 3. 15 5 Changing replay speed To play records at 45 r. p. m. Using the accessory tool provided (3a), hook the belt (3) over the larger diameter part of the motor pulley (2). When the Pro-Ject Speed Box SE is used speed change between 33 and 45 r. p. m. is available after fitting a special pulley, which may be purchased as an optional extra. For detailed product information please refer to the Pro-Ject web site www. project-audio. com. Fitting and connecting the cartridge ** All cartridges with half inch mounting holes can be fitted. Leaving the needle's protection cover on, fit the cartridge to the headshell using the screws supplied with the cartridge by passing one screw through each slot in the headshell (20). Connect the tonearm wires to the cartridge pins as follows: white left channel positive (L+) red right channel pos. (R+) green right channel return (R -) blue left channel return (L -) The full sound quality of the record player can only be achieved if the cartridge is correctly adjusted. [. . . ] Guarantee repairs will only be effected if the unit is returned correctly packaged. Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of this user guide. Please remove these parts and pack them separately: lid (10), counterweight (6), anti-skating weight (16) platter (5) and belt (3). Insert the transport lock for the tonearm (18) prior to carefully packaging the record player. Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging. [. . . ]