User manual PRINTRONIX 5000

[. . . ] User's Manual The Printronix P5000 series of Line Matrix Printers P5005B, P5205B, P5010, P5210, P5215, P5220 READ THIS SOFTWARE LICENSE AGREEMENT BEFORE USING THIS PRINTER Software License Agreement CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS BEFORE USING THIS PRINTER. USING THIS PRINTER INDICATES YOUR ACCEPTANCE OF THESE TERMS AND CONDITIONS. IF YOU DO NOT AGREE TO THESE TERMS AND CONDITIONS, PROMPTLY RETURN THE PRINTER AND ALL ACCOMPANYING HARDWARE AND WRITTEN MATERIALS TO THE PLACE YOU OBTAINED THEM, AND YOUR MONEY WILL BE REFUNDED. "Software" shall mean the digitally encoded, machine-readable data and program. [. . . ] This option allows users to define ther own lead-in characters for the Printronix Specific commands. Select a hex value for the following codes for the User Defined option: · · · Start Code 1 Start Code 2 Stop Code 162 SPC Twx Params EVFU · · Enable. The EVFU parameter allows vertical format control by the host in all four printer type modes. Vertical format control is only allowed in IMPACT/P-SERIES mode. SPC Char Set Allows you to select the print language character set. Translation Tbl Prints out a table of the Twinax interface's current character set. This operation is valid only when the Twinax interface is selected. Buffer Print · · Disable. The printer prints the EBCDIC data and control codes received from the host as hex values. Refer to page 275 for information on how to obtain a hex code printout. 163 Chapter 4 LinePrinter Plus Emulation LinePrinter Plus Emulation NOTE: When the printer is set to SPC Twx Params or SPC Coax Params, no LP+ menu items will take effect on the same offline. The LP+ Emulation resets when the printer is taken offline. * = Factory Default EMULATION (from page 136) LinePrinter+ Printer Protocol CPI/LPI Select Host Command Enable* Ignore All Ignore CPI Ignore LPI Ignore Unidir. Font Attributes Page Format Print Char. Set (see next page) Select CPI 10. 0 CPI* 12. 0 CPI 13. 3 CPI 15. 0 CPI 17. 1 CPI 20. 0 CPI Select LPI 6. 0 LPI* 8. 0 LPI 10. 3 LPI P/S Mode CPI Changed* Unchanged (see next page) (see page 166) Reset Cmd CFG Ld Disable* Power up config Current config Factory config Set Substitution Inactive* Active 164 SPC Twx Params * = Factory Default Printer Protocol (from page 164) P-Series* P-Series XQ Serial Matrix Proprinter XL Epson FX (see page 172) (see page 178) (see page 182) (see page 186) (see page 190) Font Attributes (from page 164) Typeface Prop. Spacing Bold Print Italic Print Slashed Zero Text Position Top of Line* Bottom of Line Data Processing* Disable* NLQ Enable OCR-A OCR-B High Speed NLQ Sans Serif High Speed 100 NLQ 200 DP 200 High Speed 64 BARCODE 145 BARCODE 160 Disable* Enable Disable* Disable* Forward Slant Enable Backward Slant 165 Chapter 4 LinePrinter Plus Emulation Page Format (from page 164) * = Factory Default 1These menus do not appear if the Coax or Twinax host interface is selected. 2 This value is 132 if the Coax or Twinax host interface is selected. Form Length Abs. Width MM1 345. 4* mm (0. 1-345. 4) Function of CPI 136*2 characters (1-272) Margins Left Margin1 0* columns (0-369) Right Margin1 0* columns (0-369) Bottom Margin 0* lines (0-451) Perforation Skip1 Disable* 1/2 Inch 2/3 Inch 5/6 Inch 1 inch Printer Protocol Select the LinePrinter+ protocol you wish to use. Refer to the LinePrinter Plus Programmer's Reference Manual for more information. CPI/LPI Select This parameter lets you specify the characters per inch (cpi) and lines per inch (lpi) values. 166 SPC Twx Params Host Command This parameter allows you to block certain host commands from being acknowledged by the printer. · · · · · Enable. All Unidirectional commands sent by the host are ignored by the printer. Font Attributes Typeface · Data Processing. A general purpose font printing out at 120 dpi horizontally and 72 dpi vertically. A high quality font printing at 180 dpi horizontally and 96 dpi vertically. Optical character recognition fonts printing at 120 dpi horizontally and 144 dpi vertically. A draft quality font printing at 120 dpi horizontally and 48 dpi vertically. A high quality font printing at 180 dpi horizontally and 96 dpi vertically. A draft quality font printing at 100 dpi horizontally and 48 dpi vertically. 167 · · · · · Chapter 4 LinePrinter Plus Emulation · NLQ 200. This Data Processing font prints at 200 dpi horizontally and 72 vertically. [. . . ] SHORT *, 282 LOAD PAPER, 282 ONLINE 28 CU NOT ENAB, 282 ONLINE 8344 FAILED, 282 ONLINE CU TIMED OUT, 282 PAP BAD TABLE *, 282 PAP BSY TOO LNG *, 283 PAP FIFO OVERFL *, 283 PAP FIFO UNDRFL *, 283 PAP ILLGL ST *, 283 PAP INCMPL ENER *, 283 PAP INVLD CMD *, 283 PAP INVLD PARM *, 283 PAP NOT SCHED *, 283 PAP NT AT SPEED *, 283 PAP UNEXP INT *, 283 PARAMETER ERROR, 284 PARITY ERROR, 284 PLAT INV CMD *, 285 PLAT INV PARM *, 285 PLAT INV STATE *, 285 Index POWER SAVER MODE, 285 POWERSUPPLY HOT *, 284 PRINTER HOT *, 285 PRINTER UNDER CONTROL, 278, 285 PROTECTED INSTR *, 284 PWRSUPP VOLT *, 286 RIB INVLD CMD *, 286 RIB INVLD STAT *, 286 RIBBON DRIVE, 286 RIBBON INK OUT, RIBBON, 286 SCS COMMAND ERROR, 286 SECURITY VIOLATION, 287 SF ERROR, 287 SHUTL INV CMD *, 287 SHUTL INV PARM *, 287 SHUTTLE JAM, 287 SOFTWARE ERROR *, 287 SSTACKER JAM, 288 STACK OVERFLOW *, 288 STACKER FAULT, 288 STACKER FULL, 288 TCB CORRUPTED*, 288 UNDEF INTERRUPT*, 288 UNDFNED OPCODE*, 288 UP DRV. SHORT*, 288 Fault, Centronics Parallel Interface Signals, 261 Features, printer, 11 FF After Job, 147 FF Valid at TOF, Proprinter XL Emulation, 187 FF Validity, 146 REMOTE File System, MAINT/MISC menu, 216 FIRMWARE ERROR message, 279 Flash Avail. , DIAGNOSTICS, 247 FM HEADER ERROR message, 280 Font Attributes, 167 ANSI Emulation menu, 196 Font Set, 133 CHANGE Font Size, IPDS Emulation, 204 Form Saver mode, 300 Format Control, 148, 156 FRAMING ERROR message, 280 Framing Errors, Serial submenu, 235 G Gateway address, Ethernet Parameters menu, 238 Graphic CharSize, IPDS Emulation, 206 Graphic Chek Cod, 154 Graphic Chek Err, 154 Graphics enhancement, 16 Graphics Options, 125 Absorb After ^PN, 130 Absorb After ^PY, 126 AI 00 Spaces, 128 Append Rotated, 125 Auto FF at ^PN, 130 Expanded Font, 127 I25 Selection, 128 Ignore ^Lxx Cmd. , 130 Ignore Dots, 125 317 Index Ignore Spaces, 127 IGP110 Compatbl. , 130 LP+ Font, 127 Midline PY (includes ^PN), 127 MSI Check Digit, 128 Print Quality, 127 Rot. Char Size, 126 Slash 0, 125 True Vert 1/10, 126 Truncate Alpha, 125 UPC Descenders, 126 Width Limit, 129 Graphics Quality, IPDS Emulation, 204 Graphics Scaling, IPDS Emulation, 206 GRF CHECK ERROR PRESS message, 280 Host PI, 134 HS Print (High Speed Print), P-Series XQ Emulation, 180 I I 2/5 Checksum, IPDS Emulation, 207 I 2/5 Selection, 113 I25 Selection, 128 Idle Response, Serial submenu, 235 IEEE 1284 Parallel (Bidirectional) Submenu, 219 Buffer Size in K, 220 Prime Signal, 219 TOF Action, 219 STOP IEEE 1284 Parallel Interface, 262 Byte Mode, 262 Compatibility Mode, 262 Nibble Mode, 262 Signals, 263 Ignore ^Lxx Cmd. , 130 Ignore CH#1, 132 Ignore CH#2, 132 Ignore Char, 115 Ignore Chars, 132 Ignore Dots, 125 Ignore Spaces, 127 Ignore/DB8 Setup, 132 Data Bit 8, 133 Ignore CH#1, 132 Ignore CH#2, 132 Ignore Chars, 132 H HAM. COIL OPEN * message, 280 HAMMER COIL BAD, ### Message, 280 HB NOT INSTALLD * message, 281 Hex Dump Mode, MAINT/MISC menu, 210 Hex Dump, printing, 275 Hexdump Mode, IPDS Emulation, 208 HMR BANK FAN FLT Message, 280 Host Command, 167 Host Form Length, 114 HOST INTERFACE menu, 218 Host Override, 148, 155 318 Index IGP/PGL Emulation, 105 configuring with the control panel, 107 IGP/PGL submenu, 108 Auto Uppercase, 111 Autowrap, 109 Barcode Options, 112 Compatbl. [. . . ]