User manual PRICE PUMP 3AOD-STTS-B

[. . . ] Price ® Pump Co. INSTALLATION, OPERATING AND MAINTENANCE MANUAL 3" AIR OPERATED DIAPHRAGM PUMPS METALLIC, BOLTED MODELS: 3 AOD-XXXX-B ALL ELASTOMERS PLEASE FILL IN DATA FROM YOUR PUMP NAMEPLATE Pump Model______________________ Spec. No. _________________________ Price ® Pump Company P. O. Box Sonoma, CA 95476 Tel: 707-938-8441 Fax 707-938-0764 Email: sales@pricepump. com Serial No. _________________________ RETAIN MANUAL FOR REFERENCE IN-AOD-300M-B rev. This pump was carefully inspected and subjected to final performance tests before releasing for shipment. In order to achieve maximum performance and reliability, please follow the simple instructions in this manual. [. . . ] Tighten outer clamping plate but do not torque down completely until later in the reassembly. Depress one of the diaphragm assemblies completely into one of the air valve halves (86). Set this side flat onto a clean flat surface so that the other diaphragm is facing up. Carefully align the Gortex tape (51) along the outer bead of the diaphragm. Now align the taped outer bead of the diaphragm with the groove on the air valve half (86). Place the pump chamber (1) over the diaphragm so that the bead on the diaphragm is aligned with the groove on the pump chamber. Assemble the pump chamber ( 1) to the air valve half (86) using twelve capscrews (9) flat washers (96). Torque each capscrew, using a "Cross-Sequence" to: IN-AOD-300M-B rev. Turn the unit over so that it is resting on the pump chamber (1) previously fastened. Turn unit upside down so that it is resting on the discharge flange of the pump chamber (1) and the suction flange is facing up. Insert ball valve (29), "O"-ring (47), ball valve seat (28) and "O"-ring (47) into each suction port of the pump chamber (1). Check to make sure the surface of the "O"-ring is above the surface of the pump chamber flange. Fasten the suction manifold (24) to each pump chamber (1) using eight lock washers (53) and capscrews (52). Place a ball valve (29), "O"-ring (47), ball valve seat (28), and "O"-ring (47) into each discarge manifold flange (23). Check to make sure the surface of the "O"ring is above the surface of the manifold flange. Fasten the discharge manifold (23) to each pump chamber (1) using eight lock washers (53) and capscrews (52). Note that the suction and discharge manifolds can be oriented to fit the installation requirements. If it becomes necessary to replace the sleeve bearings, they can be pressed out of each bore. The shaft seals can be removed by prying them out with a small screwdriver or similar blunt tool. Inspect the muffler for damage or any debris that may be trapped inside. Clean any exposed passages to ensure complete and unobstructed air flow. Should the interior surfaces be coated with oil, clean thoroughly all internal passages and both main and pilot spools prior to reassembly. [. . . ] All claims for defective products or parts under this warranty must be made in writing immediately upon discovery and, in any event, within two (2) years of shipment by seller and all claims for defective work must be made in writing upon discovery. ANY UNAUTHORIZED DISASSEMBLY, ALTERATION OF OR TAMPERING WITH ANY PRODUCT OR COMPONENT MAY VOID THE WARRANTY, IN THAT SUCH ACTION WILL RESULT IN SELLER BEING RELEASED AND RELIEVED FROM ITS OBLIGATIONS UNDER THIS WARRANTY AND FOR ANY FURTHER COSTS OR CATIONS UNDER CLAUSE 7. C, FOLLOWING, AND THE BUYER ASSUMING SOLE RESPONSIBILITY FOR THE COSTS AND RESULTS OF SUCH ACTION. THE FOREGOING S EXPRESS, IMPLIED AND STATUTORY, INCLUDING WITHOUT LIMITATION, THE IMPLIED, WARRANTIES OF MERCHANTABILITY AND FITNESS. ANY PRODUCT (S) SOLD HEREUNDER WHICH IS NOT MANUFACTURED BY SELLER ARE NOT WARRANTED BY SELLER and shall be covered only by the express warranty, if any, of the manufacturer thereof. [. . . ]