User manual PRECISION POWER S200.2

[. . . ] PRECISION POWER HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. BY PURCHASING THIS PRODUCT, THE CONSUMER AGREES AND CONSENTS THAT ALL DISPUTES BETWEEN THE CONSUMER AND PRECISION POWER SHALL BE RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN LOS ANGELES COUNTY, CALIFORNIA. Some states do not allow limitation on how long an implied warranty lasts. In such states, the limitation or exclusions of this Limited Warranty may not apply. [. . . ] In such states, the exclusion or limitation of this Limited Warranty may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights which vary from state to state. 2010 Sedona Series Components S200. 2 You're smart enough to buy these Sedona Series Components, be smart enough to read this manual. . . Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Practice Safe Sound!What's In the Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Tools of the Trade Speaker Mounting Locations Door Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Rear Deck Mounting Installing the Mid-bass Installing the Mid-bass (cont. ). . . . . . . . . . . . . . . . . . . . . . . . 6 Surface Mounting the Tweeter. . . . . . . . . . . . . . . . . . . . . . . . 7 Flush Mounting the Tweeter, Fixed Panel. . . . . . . . . 8 Flush Mounting the Tweeter, Removable. . . . . . . . . . 9 Installing the Crossover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Crossover Wiring Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Limited Consumer Warranty. . . . . . . . . . . . . . . . . . . . . . . . . 12 SEDONA PASSIVE CROSSOVER (COVERS REMOVED) WIRING DIAGRAM TW- TW+ W- W+ IN- IN+ Radio or Amplifier Nominal Impedance Power Handling (continuous/peak) Frequency Response Sensitivity (1w/1m) Woofer Mounting Depth Woofer Mounting Diameter Tweeter Mounting Depth 4 Ohm 100w 70-20kHz 92db 2. 25" (2 1/4") 5. 625" (5 5/8") . 875" (7/8") INSTALLING THE CROSSOVER Step 1: Find a location for the crossover away from any factory or aftermarket electrical wires. It is recommended to mount the passive crossover close to the amplifier. Step 4: Remove crossover and pre-drill mounting holes using a 1/8" drill bit. WARNING: Window mechanisms, electrical wires, and other expensive car parts have a nasty habit of hiding where you least expect. The input terminals (IN) should be connected to the source (radio or amplifier). Changing the polarity of the tweeter may be necessary for optimum sound quality. Step 7: Re-install the crossover cover. INTRODUCTION Thank you for your purchase of this Sedona Series Component Loudspeaker System from PrecisionPowerTM. Our engineers have combined state of the art materials such as formed prolypropylene cones and mylar dome tweeters with cutting edge industrial design to achieve competition-ready performance levels. Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss. Step 4: If not using a hole saw, use either the cardboard packaging for the tweeters or the surface mount trim ring as a template to mark the proper size hole. Step 5: With the tweeter assembled, route the wires through the hole and the pressure ring and slip the pressure ring over the tweeter assembly. Step 6: Align the tweeter so the logo faces the desired direction then push the pressure ring on to the rear of the tweeter assembly until the tweeter is snugly mounted to the panel. Step 7: Connect the speaker wires observing the correct polarity and re-assemble the panel. DOOR MOUNTING When considering possible speaker locations in the doors, be sure to check the operation of the window mechanism and all other moving parts inside the door. Most vehicles use a stabilizer stop bar in between the door and the door jamb. This bar prevents the door from opening too far, but may intrude into the speaker mounting area when the door is closed. Many do-it-yourself installers overlook this and check for speaker clearance only when the door is fully open. REAR DECK MOUNTING In rear deck installations, check the operation of the trunk suspension springs or tension bars. These tension bars can move when opening and closing the trunk and can exert a great deal of force against anything that obstructs their movement, such as a speaker basket or motor assembly. In addition, try to avoid locating the speakers too close to the back edge of the rear deck. Installing the rearmost screws may not be possible without the removal of the rear window. [. . . ] INSTALLING THE MID-BASS Step 1: Determine where the speaker will be mounted. Make sure there is a flat area large enough for the speaker to fit properly. An uneven mounting surface can damage the driver and limit the bass performance of your Sedona Series component system. Step 2: Check to make sure the mounting location you have chosen for the speaker will not interfere with the operation of the vehicle. [. . . ]