User manual PRECISION POWER FRX 322

[. . . ] BACK TO CONTENTS FEATURES / SPECIFICATIONS 3-Way Active Crossover 12dB/octave Slopes Low Pass Level Control Input Attenuation Switch Detented Frequency Selection Controls Gold RCA Input and Output Connectors PowerLock Power, Ground and Remote Connector PWM Power Supply Designed and Handcrafted in the USA Specifications Signal-to-Noise Ratio >102dB Total Harmonic Distortion (1KHz, 1VRMS) 0. 002% Input Impedance 10 k Maximum Output (10 k Load) 8 VRMS Supply Voltage 11-15 VDC Crossover Slopes 12 dB/octave Crossover Frequencies: Low Pass 40Hz to 500Hz Front High Pass 40Hz to 5kHz Rear High Pass 40Hz to 500Hz Dimensions 6. 813" W 0. 995" H 3. 805" D 1 BACK TO CONTENTS MOUNTING Mounting To prevent damage to the FRX-322 while driving, mount it in a secure place. Choosing the appropriate location will depend upon your vehicle and the complexity of your system design. Typical mounting locations for your new FRX-322 would be in the dash or center console. Never mount the component in a location that would subject it to immersion or exposure to water. Once a location has been chosen, securely mount the FRX-322 using the two supplied brackets. [. . . ] This wire supplies a 12 volt T/O B+ signal to the FRX-322 when the main system is activated. Once you have routed the power, Quick Disconnect ground, and remote wires through the vehicle, it is time to connect the wires to the FRX-322. Be sure that you have not reconnected the ground cable to the negative post of the battery. Cut off excess wire and, using wire strippers, strip the power, ground and remote cables about 1/8 inch. With a small flat-bladed screwdriver, loosen the screws before attempting to insert the cables. After you have inserted the stripped end of each cable into the connector, secure it by tightening the associated screw. If the wires are secure, the connector may be plugged into the FRX-322. Power After connecting the Power, Ground and Remote wires, plug in the PowerLock connector here. Low Pass Output Plug the RCA cables from the FRX to the Low Pass amplifier inputs. Front Input Plug the RCA cables from the front channel output of the headunit to the FRX Front Input RCAs. Rear Input Plug the RCA cables from the rear channel output of the headunit to the FRX Rear Input RCAs. Front High Pass Out Plug the RCA cables from the FRX to the Front High Pass amplifier inputs. Rear High Pass Out Plug the RCA cables from the FRX to the Rear High Pass amplifier inputs. 1 2 3 4 5 6 Power R L R Front Input L R Rear Input L R L R L Low Pass Output Front High Pass Out Rear High Pass Out PrecisionPower FRX-322 Made in USA 6 BACK TO CONTENTS FUNCTIONS 1 250 0dB 300 -10 +5 +7 +10 250 250 300 100 300 400 40 500 Power 100 50 40 FRX-322 100 50 40 400 -20 500 - 400 50 500 Low Pass Freq. Low Pass Level Front/Rear Input Connect Attenuation -12dB in Front Rear X 10 High Pass Freq. Low Pass Frequency Used to set the Low Pass Frequency (40 Hz - 500 Hz) 3. Low Pass Level Low Pass Level can cut or boost the Low Pass Frequency (- to +10dB) 4. Front/Rear Input Connect Push this switch IN to connect front and rear channels together when using one input. Attenuation -12dB in Push this switch IN for attenuation if the line level is over 6 volts. X10 Push this switch IN to multiply the Front High Pass frequency range by 10. Front High Pass Frequency Used to set the Front High Pass Frequency (40 Hz - 5 kHz) 8. Rear High Pass Frequency Used to set the Rear High Pass Frequency (40 Hz - 500 Hz) 7 BACK TO CONTENTS INPUT To use Speaker Level Inputs (common ground headunits only), connect RCA plugs to the front or rear speaker leads as shown, and push IN the Attenuation switch. SOURCE Headunit eject 1 5 BASS VOLUME LEFT TREBLE TRACK RIGHT FOWARD REVERSE PPI 2 6 3 7 4 8 Trk 1 MAR KET ING DPT BALANCE (+) Positive LEFT input (-) Negative (+) Positive RIGHT input (-) Negative WARNING: If you are using a source unit with bridged high powered (or "floating ground") speaker outputs, a suitable high to low level adapter must be used. If you are unsure about your head unit see your local PPI dealer or call 1-800-62POWER. Pow er R L Ouow Pass tput L R InpFront ut L R InpRear ut L R High Fro Pass nt Out Pow er 100 50 250 300 -10 0 - 0dB +5 FRX-3 22 ec Pr 400 -2 500 Powe r L R High Re Pass ar Out L isi on 40 Low Pass Freq . +7 Low Pass +10 Leve FRX -32 2 A US in de Ma l Fro Inpu nt/Rear t Co nne ct Atte nu -12d ation B in X 10 100 50 250 300 100 50 40 250 300 400 40 400 High Push In to attenuate the input. Pass Fron t 500 Freq . H igh Pass Rear 500 Freq . 8 BACK TO CONTENTS TROUBLE SHOOTING NO SOUND Is the LED lit? YES Check Input cables for signal by connecting them straight to the Subwoofer amplifier NO Check Power and Remote turn-on wire for voltage. local Authorized PrecisionPower Dealer Check head unit and amplifiers. [. . . ] Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts; so the above limitations or exclusions may not apply to you. Your product will be serviced on an in-warranty basis within the warranty period for the correction of warranted defects. If improper operation of your PrecisionPower product should occur, contact your Authorized Dealer for assistance with the return and factory repair of your PrecisionPower product. If an Authorized Dealer is not available, return the unit including your name, telephone number, return address, a copy of your sales receipt, and a description of the problem to: PrecisionPower, Inc. [. . . ]