User manual POWERDSINE PD-6024

[. . . ] 5 1. 2 Power Cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 ABOUT THE POWER OVER LAN MIDSPAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2. 1 Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2. 2 10/100BASE-TX Ports Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2. 2. 1 Data Input Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The power socket outlet must be near the Midspan and be easily accessible. You can only remove power from the unit by disconnecting the power cord from the outlet. This unit operates under SELV (Safety Extra Low Voltage) conditions according to EN60950/IEC 950. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions. If your supplies are of IT type, this unit must be powered by 230 V (2P+T), via an isolation transformer with a ratio of 1:1 and with the secondary connection point labeled Neutral, connected directly to ground. only: The Power over LAN Midspan is covered by General Approval, NS/G/12345/J/100003, for indirect connection to a public telecommunications system. Switzerland Power over LAN Solutions 6 Cat. No. : 06-6800-056 PD-6006/12/24 2 About the Power over LAN Midspan PowerDsine's family of Power over LAN Midspans, series 6000, injects power over data-carrying Ethernet cabling. The PD-6006/6012/6024 Midspans, support 6, 12 and 24 ports respectively in a 10/100BaseTx Ethernet network, over TIA/EIA-568 Category 5/5e/6 cabling. DC operating power, for data terminal units, is fed over unused pairs of the cabling (7/8 and 4/5). The Power over LAN Midspan normally powers devices that are Power over LAN enabled or are equipped to receive power over Ethernet. Devices that are not equipped to receive power over Ethernet may require an external power adapter in order to be powered. Power over LAN Midspan main features: Remote power feeding of Ethernet terminals Eliminates the need for AC outlets, local UPS and AC/DC adapters Universal range power input (100-240 VAC, 50/60 Hz and/or 46 to 57 VDC) Power management SNMP management (optional) Independent overload and short-circuit protection per channel Port status indications Standard 19-inch rack mountable. 2. 1 Power Management When establishing a network, the total power required by PDs may exceed the total power available from the Midspan. The built-in Power Management feature will not allow the total power output to exceed the maximum power available (refer to the Technical Specifications). When the total power available is near maximum, attempts to connect an additional PD to a free port will cause the corresponding LED of the port to blink orange, indicating an outof-power budget. Power distribution is based on "first come, first served" logic. It is possible that connected and operating PDs will significantly increase or suddenly raise their power requirements. If the power required exceeds the power available, the Power over LAN Midspan will start to turn off ports, starting from the last port down, until the total power is once again under the maximum limit. No. : 06-6800-056 PD-6006/12/24 2. 2 2. 2. 1 10/100BASE-TX Ports Definition Data Input Ports According to the model acquired, the Midspan has 6, 12 or 24 10BaseT/100Base-TX- data input ports, configured in a non-crossover manner (straight-wired). These ports, shown in Figure 2-1 (bottom row of connectors), are designed to carry Ethernet data only (Tx/Rx) over the standard 2-wire pairs (pins 1/2 and 3/6). Data & Power Output Ports 2. 2. 2 The Midspan has 6, 12 or 24 Data & Power ports also configured in noncrossover manner (straight-wired). These ports are designed to carry Ethernet data over the standard 2-wire pairs (pins 1/2 and 3/6) and DC power over the spare pairs (pins 4/5 and 7/8). The Power over LAN Midspan is not a repeater. As such, the maximum distance from the Ethernet switch is not to exceed 100 meters (328 ft). In accordance with the IEEE 802. 3 standard, the Power over LAN Midspan is guaranteed to work up to this distance. Figure 2-1: Power over LAN Midspan, Front View (PD-6024) 2. 3 Indicators A set of indicators provide the status of the Power over LAN Midspan and its ports. [. . . ] During these conditions, port power is disconnected. Technical Specifications Physical Specifications Dimensions (h x w x l) Weight 44 x 433 x 302 mm (1. 75 x 17 x 11. 9 inch) 4 kg (8. 8 lb) Environmental Specifications Temperature - Operating - Storage Humidity 0 to 40 °C (32 to 104 °F) -20 to 70 °C (-4 to 158 °F) 10 to 90% (non-condensing) Electrical Specifications Parameter AC Input Voltage DC Input Voltage Input Current @ 115 VAC Input at 48 VDC Total Output Power (1) Output Power, per Port Nominal Output Voltage Total Output Power (2) (1) Using AC Power (2) Using DC power PD-6006 PD-6012 90 to 264 VAC at 47-63 Hz 46 to 57 VDC 4 A max. 44 to 57 VDC 400 W 200 W max. 15. 4 W (not to exceed Total Output Power) Power over LAN Solutions 14 Cat. No. : 06-6800-056 PD-6006/12/24 4 Remote Power Management SNMP Remote Management is an optional feature, for monitoring and control of the device. For further details, refer to PowerDsine's PowerView, Power over LANTM SNMP Web Manager User Guide, catalog number 06-6910-056. [. . . ]