User manual POULAN PRO PP4620AVX

[. . . ] www. poulan-pro. com 1-800-554-6723 Instruction Manual Manual de Instrucciones Manuel d'Instructions PP4620AVX ESPAÑOL WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury. ADVERTENCIA: Lea el manual de instrucciones y siga todas las advertencias e enstrucciones de seguridad. El no hacerlo puede resultar en lesiones graves. AVERTISSEMENT: Lire le manuel d'instructions et bien respecter tous les avertissements et toutes les instructions de sécurité. Tout défaut de le faire pourrait entraîner des blessures graves. Poulan PRO 1030 Stevens Creek Road Augusta, GA 30907 Poulan PRO 850 Matheson Blvd. [. . . ] If engine still fails to start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723. CHAIN BRAKE WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. The chain brake should be replaced by an authorized service dealer if any part is worn to less than 0. 020 (0. 5 mm) thick. Repairs on a chain brake should be made by an authorized service dealer. Take your unit to the place of purchase if purchased from a servicing dealer, or to the nearest authorized master service dealer. The brake is designed to stop the chain if kickback occurs. checked several times daily. This is the only instance when the saw should be placed on the ground with the engine running. Grip the rear handle with your right hand and the front handle with your left hand. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately. Braking function control CAUTION: The chain brake must be Inertia activating function control WARNING: When performing the following procedure, the engine must be turned off. Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14 (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the tip of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate. CUTTING METHODS IMPORTANT POINTS S Check chain tension before first use, after 1 minute of operation, and each time before you start the chain saw. Do not cut metal, plastics, masonry, non-wood building materials, etc. If the chain jumps off the guide bar, inspect the chain for damaged drive links before reinstalling. Burrs on drive links, which prevent them from entering the groove of the guide bar, can be removed with a flat file. Even a small amount of dirt will dull a chain, increase the possibility of kickback, and require chain sharpening or replacement. S Practice cutting a few small logs using the following techniques to get the "feel" of using your saw before you begin a major sawing operation. S Squeeze the throttle trigger and allow the engine to reach full speed before cutting. If you force the cut, damage to the bar, chain, or engine can result. 11 S Release the throttle trigger as soon as the cut is completed, allowing the engine to idle. If you run the saw at full throttle without a cutting load, unnecessary wear can occur to the chain, bar, and engine. S To avoid losing control when cut is complete, do not put pressure on saw at end of cut. [. . . ] MANUFACTURER'S WARRANTY COVERAGE: If any emissions related part on your engine (as listed under Emissions Control Warranty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part, the part will be repaired or replaced by Poulan PRO. OWNER'S WARRANTY RESPONSIBILITIES: As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your instruction manual. Poulan PRO recommends that you retain all receipts covering maintenance on your small off-road engine, but Poulan PRO cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the small off-road engine owner, you should be aware that Poulan PRO may deny you warranty coverage if your small off-road engine or a part of it has failed due to abuse, neglect, improper maintenance, unapproved modifications, or the use of parts not made or approved by the original equipment manufacturer. [. . . ]