User manual POULAN PRO PP333

[. . . ] Veuillez ne pas retourner le produit au détaillant. 1-800-554-6723 Register your product online at: Registre su producto en línea en: Enregistrez votre produit en ligne à l'adresse : www. poulanpro. com Instruction Manual Manual de Instrucciones Manuel d'Instructions ESPAÑOL PP333 For Occasional Use Only WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. ADVERTENCIA: Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad. AVERTISSEMENT: Lire le manuel d'instructions et bien respecter tous les avertissements et toutes les instructions de sécurité. Tout défaut de le faire pourrait entraîner des blessures graves. Poulan PRO 7349 Statesville Road Charlotte, NC 28269 Poulan PRO 850 Matheson Blvd. [. . . ] You will achieve the best performance and minimum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below. Tip of the line does the cutting. Line crowded into work area. Eye Protection Right Cut from your left to your right. When operating unit, clip shoulder strap onto clamp, stand as shown and check for the following: Wrong 12 S The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences. S For trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially: S During light duty cutting. S Near objects around which the line can wrap such as small posts, trees or fence wire. TRIMMING - Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Trimming Sweeping 3 inches (8 cm) above ground SCALPING - The scalping technique removes unwanted vegetation down to the ground. Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. Scalping S Blade Thrust is a reaction that only occurs when using a bladed unit. It is important that you understand what causes blade thrust, how you can reduce the chance of its occurring, and how you can remain in control of unit if blade thrust occurs. S WHAT CAUSES BLADE THRUST - Blade Thrust can occur when the spinning blade contacts an object that it does not cut. This contact causes the blade to stop for an instant and then suddenly move or "thrust" away from the object that was hit. The "thrusting" reaction can be violent enough to cause the operator to be propelled in any direction and lose control of the unit. The uncontrolled unit can cause serious injury if the blade contacts the operator or others. S WHEN BLADE THRUST OCCURS Blade Thrust can occur without warning if the blade snags, stalls, or binds. This is more likely to occur in areas where it is difficult to see the material being cut. By using the unit properly, the occurrence of blade thrust will be reduced and the operator will be less likely to lose control. OPERATING INSTRUCTIONS FOR USE WITH WEED BLADE MOWING - Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach. Avoid pressing the head into the ground as this can scalp the ground and damage the tool. Mowing SWEEPING - The fanning action of the rotating line can be used to blow away loose debris from an area. Keep the line parallel to and above the area surface and swing the tool from side to side. 13 S Cut only grass, weeds, and woody brush up to 1/2 inch (1 cm) in diameter with the weed blade. Do not let the blade contact material it cannot cut such as stumps, rocks, fences, metal, etc. , or clusters of hard, woody brush having a diameter greater than 1/2 inch (1 cm). [. . . ] MANUFACTURER'S WARRANTY COVERAGE: If any emissions related part on your engine (as listed under Emissions Control Warranty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part, the part will be repaired or replaced by Poulan PRO. OWNER'S WARRANTY RESPONSIBILITIES: As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your instruction manual. Poulan PRO recommends that you retain all receipts covering maintenance on your small off-road engine, but Poulan PRO cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the small off-road engine owner, you should be aware that Poulan PRO may deny you warranty coverage if your small offroad engine or a part of it has failed due to 21 abuse, neglect, improper maintenance, unapproved modifications, or the use of parts not made or approved by the original equipment manufacturer. [. . . ]