User manual POULAN PR621ES

[. . . ] IMPORTANT MANUAL Do Not Throw Away OWNER'S MANUAL MODEL NUMBER: PR621ES SNOW THROWER Read the Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. WARNING: Always Wear Eye Protection During Operation 436439 08. 13. 10 TH Printed in the U. S. A. CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and manufactured to give best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. [. . . ] Key Figure 17 Adjusting the Discharge Chute and Chute Deflector To adjust the discharge chute, move deflector chute handle left or right to desired position (Figure 18). 1 3 2 Figure 19 Preventing Freeze-up after Use · Let the engine run for a few minutes to prevent moving parts from freezing. Stop the engine, wait for all moving parts to stop, and remove ice and snow from the snowthrower. Rotate the discharge chute left and right to free it from any ice buildup. With the ignition key in the Off position, pull the recoil starter handle several times or connect the electrical cord to a power source and the snowthrower and push the electric start button once to prevent the recoil starter and/or the electric starter from freezing up. In snowy and cold conditions, some controls and moving parts may freeze. If you have difficulty operating any control or part, start the engine and let it run for a few minutes. · · · Figure 18 1. Chute handle To raise or lower the angle of the chute deflector, loosen the chute deflector knob on the chute deflector and move the chute deflector up or down (Figure 18). 10 · Operating Tips · The auger blades can throw stones, toys, and other foreign objects and cause serious personal injury to the operator or to bystanders. · Keep the area to be cleared free of all objects that the auger blades could pick up and throw. · Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower. · · · · · · The best time to remove snow is the early morning. At this time the snow is usually dry and has not been exposed to the direct sun and warming temperatures. Slightly overlap each successive path to ensure all snow will be removed. For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly. After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine. Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use. Maintenance NOTE: Determine the left and right sides of the machine from the normal operating position. 11 Adjusting the Control Cable Checking the Control Cable Release the control bar to remove the slack in the control cable (Figure 20). Adjusting the Control Cable 1. With the control bar disengaged, unhook and move the control cable to the highest position. 1 Position 2 2 1 Position 1: Default position (Lower Hole as shown in illustration) 3 Figure 21 1. Control bar IMPORTANT: The control cable must contain some slack when you disengage the control bar for the auger blades to stop properly. NOTE: You may need to adjust the control cable from position 1 (default) to position 2 if you notice belt slip when the control bar is engaged. NOTE: If the control cable is adjusted to position 2, ensure that the auger stops properly when the control bar is released Inspecting the Auger Blades Before each session, inspect the auger blades for wear. [. . . ] 25 REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621ES (96182000400) DRIVE ASSEMBLY 1 7 2 8 3 4 5 6 11 9 12 10 SSST-Drive asm_3 13 KEY NO. 434860 434502 426490 851074 437261 430817 434859 434848X431 166043 17060620 199092 17060620 435383 436439 QTY 1 1 1 1 1 1 1 1 1 1 1 1 1 1 DESCRIPTION SPACER. ENGINE. CRANK KEEPER. ENGINE. BELT PULLEY. ENG. TRACTION. 3/4 WASHER. HARDEN BELT-V. TRACTION SCREW. CAP . SCHD. 3/8-24 X 1. 25 SPRING. IDLER. PULLEY. RETURN ARM. IDLER. PNT. MS431 PULLEY. IDLER. BACKSIDE SCREW. HXWH. THDRL. 1/4-20X1-1/4 SPACER. RETAINER SCREW. 3/8-16X1. SMGML. TAP/R. BLK PULLEY. DRIVEN OWNER'S. MANUAL. ENGLISH/FRENCH NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm IMPORTANT: Use only Original Equipment Manufacturer (O. E. M. ) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. [. . . ]