User manual POULAN PRO PPB5500P

[. . . ] Veuillez ne pas retourner le produit au détaillant. 1-800-554-6723 Register your product online at: Registre su producto en línea en: Enregistrez votre produit en ligne à l'adresse : www. poulanpro. com Instruction Manual Manual de Instrucciones Manuel d'Instructions ESPAÑOL PPB5500P WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Refer to your original manual for additional Warnings and Operating Instructions. ADVERTENCIA: Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad. Refiera a su manual original para las Instrucciones de Funcioniamiento y las Advertencias adicionales. [. . . ] Push the attachment into the coupler until the locking/release button snaps into the primary hole. Coupler Primary Hole Guide Recess 6 Locking/ Release Attachment Button 5. Repeat steps to attach extension shaft to coupler on engine end shaft. Before using the unit, tighten both knobs securely by turning clockwise. Make sure the locking/ release button is locked in the primary hole of both couplers and the knobs are securely tightened before operating the unit. Using the wrong holes could lead to serious injury or damage to the unit. WARNING: Upper Shoulder Strap Clamp ENGINE/MOTOR END Lower Shoulder Strap Clamp ATTACHMENT END Screws Locking/Release Button in Primary Hole SHOULDER STRAP ASSEMBLY WARNING: Proper shoulder strap and handle adjustments are required before use. The shoulder strap clamp must be installed as shown above the assist handle on the engine end shaft. These tabs are provided to adapt this attachment for use with units that have a 1 inch (2, 5 cm) diameter shaft (the shoulder strap clamp will not tighten down securely on the 1 inch (2, 5 cm) diameter shaft without using these spacer tabs). The tabs must be broken off completely before use and placed over the screw holes on the lower shoulder strap clamp. These tabs are not needed for units with a 7/8 (2, 2 cm) shaft. LOWER SHOULDER STRAP CLAMP Spacer Tabs 3. Try on shoulder strap and adjust for fit and balance before starting the engine or beginning a cutting operation. Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist. NOTE: A one-half twist is built in the shoulder strap to allow the strap to rest flat on the shoulder. Adjust the strap, allowing the hook to be about 3 - 6 inches (8 - 15 cm) below the waist. Fasten the strap hook to the upper clamp and lift the tool to the operating position. Shoulder Strap Shoulder Strap Clamp Spacer Tabs positioned for use on 1 inch (2, 5 cm) diameter shaft ADJUSTING THE ASSIST HANDLE WARNING: When adjusting the assist handle, be sure it remains directly above the coupler on the engine end shaft to ensure proper balancing of unit. Assist Handle 1. Place the upper shoulder strap clamp over the shaft above the assist handle. Position the lower shoulder strap clamp under the upper shaft and align the upper and lower clamp screw holes (use spacer tabs between upper and lower clamps if necessary to secure clamp, i. e. for 1 inch (2, 5 cm) diameter shaft). Coupler 7 OPERATION KNOW YOUR PRUNER ATTACHMENT READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR PRUNER ATTACHMENT. Compare the illustrations with your attachment to familiarize yourself with the location of the various controls and adjustments. Pruner Hanger Bar Oil Fill Cap Chain Shaft Extension Shaft Bar Bar Nut PRUNER The PRUNER is designed for removal of limbs and branches overhead not greater than 6 inches (15 cm) in diameter. CHAIN TENSION It is normal for a new chain to stretch during first 15 minutes of operation. Locking/Release Button OPERATING THE COUPLER Your unit is equipped with a coupler system which enables optional attachments to be installed. [. . . ] Slide guide bar behind sprocket until guide bar stops against sprocket. Hold chain with the drive links as shown. Cutter Top Plate Side Plate S File chain to meet the specifications as shown. 75° 60° 30° Hook Angle 0. 025 inch (0. 65 mm) Rounded Corner Squared Off Corner Tip of Bar Drivelink Right Too Much Hook Angle CUTTERS MUST FACE IN DIRECTION OF ROTATION Wrong Cutters Depth Gauge WARNING: Maintain the proper hook angle according to the manufacturer's specifications for the chain you are using. Improper hook angle will increase the chance of kickback which can result in serious injury. Drive Links 12 12. [. . . ]