User manual POULAN PRO PP5000P

[. . . ] Veuillez ne pas retourner le produit au détaillant. 1-800-554-6723 Register your product online at: Registre su producto en línea en: Enregistrez votre produit en ligne à l'adresse : www. poulanpro. com Instruction Manual Manual de Instrucciones Manuel d'Instructions ESPAÑOL PP5000P WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Refer to your original manual for additional Warnings and Operating Instructions. ADVERTENCIA: Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad. Refiera a su manual original para las Instrucciones de Funcioniamiento y las Advertencias adicionales. [. . . ] Push the attachment into the coupler until the locking/release button snaps into the primary hole. Before using the unit, tighten the knob securely by turning clockwise. Coupler Primary Hole Guide Recess S Hex wrench (provided) tachments, place the unit on a flat surface for stability. Coupler INSTALLING PRUNER ATTACHMENT CAUTION: When removing or installing at- Upper Shaft Locking/ Release Attachment Button Attachment LOOSEN WARNING: Make sure the locking/ release button is locked in the primary hole and the knob is securely tightened before operating the unit. Using the wrong hole could lead to serious injury or damage to the unit. Knob TIGHTEN 6 Locking/Release Button in Primary Hole SHOULDER STRAP ASSEMBLY WARNING: Proper shoulder strap and handle adjustments are required before use. The shoulder strap clamp must be installed as shown above the assist handle on the upper shaft (powerhead end of unit). These tabs are provided to adapt this attachment for use with powerheads that have a 1 diameter upper shaft (the shoulder strap clamp will not tighten down securely on the 1 diameter upper shaft without using these spacer tabs). The tabs must be broken off completely before use and placed over the screw holes on the lower shoulder strap clamp. These tabs are not needed for powerheads with a 7/8 upper shaft. LOWER SHOULDER STRAP CLAMP Spacer Tabs 3. Try on shoulder strap and adjust for fit and balance before starting the engine or beginning a cutting operation. Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist. NOTE: A one-half twist is built in the shoulder strap to allow the strap to rest flat on the shoulder. Adjust the strap, allowing the hook to be about 3 - 6 inches (8 - 15 cm) below the waist. Fasten the strap hook to the upper clamp and lift the tool to the operating position. Shoulder Strap Shoulder Strap Clamp ADJUSTING THE ASSIST HANDLE Spacer Tabs positioned for use on 1 diameter upper shaft WARNING: When adjusting the assist handle, be sure it remains directly above the coupler on the engine end shaft to ensure proper balancing of unit. Assist Handle 1. Place the upper shoulder strap clamp over the upper shaft above the handlebar. Position the lower shoulder strap clamp under the upper shaft and align the upper and lower clamp screw holes (use spacer tabs between upper and lower clamps if necessary to secure clamp, i. e. Upper Shoulder Strap Clamp POWERHEAD END Coupler Lower Shoulder Strap Clamp ATTACHMENT END Screws 7 OPERATION KNOW YOUR PRUNER ATTACHMENT READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR PRUNER ATTACHMENT. Compare the illustrations with your attachment to familiarize yourself with the location of the various controls and adjustments. Hanger Pruner Coupler Shaft Bar oil fill cap Chain Bar PRUNER The PRUNER is designed for removal of limbs and branches overhead not greater than 6 inches (15 cm) in diameter. CHAIN TENSION Bar nut It is normal for a new chain to stretch during first 15 minutes of operation. Locking/Release Button OPERATING THE COUPLER Your powerhead is equipped with a coupler which enables optional attachments to be installed. PP4000C *not designed for use with electric powerheads Always disconnect powerhead spark plug (or disconnect powerhead from power source) before removing or installing attachments. Attachment Coupler Upper Shaft 3. [. . . ] Move ON/STOP switch to the STOP position and disconnect spark plug (or disconnect powerhead from power source). Turn adjusting screw by hand counterclockwise until adjusting pin just touches the stop. Slide guide bar behind sprocket until guide bar stops against sprocket. Hold chain with the drive links as shown. Cutter 30° Hook Angle 0. 025 inch (0. 65 mm) Rounded Corner Squared Off Corner Right Too Much Hook Angle Tip of Bar Drivelink Wrong CUTTERS MUST FACE IN DIRECTION OF ROTATION 12 Cutters Depth Gauge 11. [. . . ]