User manual POULAN PRO PP10530ES

[. . . ] IMPORTANT MANUAL Do Not Throw Away OWNER'S MANUAL MODEL NUMBER: WARNING: Read the Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. PP10530ES SNOW THROWER Always Wear Eye Protection During Operation 407885 08. 03. 06 BY Printed in U. S. A. IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. [. . . ] Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer. When the engine starts, release the recoil starter handle and slowly move the choke control to the OFF position. Engine will not develop full power until it has reached normal operating temperature. WARM START - RECOIL STARTER Follow the steps above, keeping the choke in the OFF position. BEFORE STOPPING Run the engine for a few minutes to help dry off any moisture on the engine. To avoid possible freeze-up of the starter, proceed as follows: 13 ELECTRIC STARTER 1. Plug the other end of the power cord into a three-hole grounded 120 Volt A. C. While the engine is running, push starter button and spin the starter for several seconds. NOTE: The unusual sound made while starter is spinning will not harm the engine or starter. Disconnect the power cord from the receptacle first, then from the engine. While the engine is running, pull the recoil starter handle with rapid, full arm strokes three or four times. NOTE: The unusual sound made while pulling the recoil starter handle will not harm the engine or starter. IF RECOIL STARTER HAS FROZEN If the recoil starter has frozen and will not turn the engine, proceed as follows: 1. Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible. Release the recoil starter handle and let it snap back against the starter. If the engine still fails to start, repeat the above steps or use the electric starter. SNOW THROWING TIPS · · · · Always operate the snow thrower with the engine at full throttle. It is easier and more efficient to remove snow immediately after it falls. At this time the snow is usually dry and has not been exposed to the direct sun and warming temperatures. Slightly overlap each successive path to ensure all snow will be removed. [. . . ] 1 inch = 25. 4 mm IMPORTANT: Use only Original Equipment Manufacturer (O. E. M. ) replacement parts. Failure to do so could be hazardous, damage your unit and void your warranty. 29 REPAIR PARTS WHEELS / DECALS SNOW THROWER - MODEL PP10530ES (96192001200) 10 30 15 32 12 19 11 11 18 10 13 14 27 20 17 7 8 28 31 4 23 33 21 3 4 24 9 22 25 26 11 29 7 4 28 2 34 29 2 10 18 30 14 15 12 27 28 25 24 21 33 23 26 28 11 4 22 3 1 16 19 34 32 13 20 11 1 2 4 12 9 8 6 5 1 3 30 11 10 7 REPAIR PARTS WHEELS / DECALS SNOW THROWER - MODEL PP10530ES (96192001200) KEY PART NO. NO. DESCRIPTION 1 2 3 4 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 192092X421 155443 405161 184471 17000616 185603X479 185602X479 17600406 198584 406057 193506X498 182015 194944X008 194939X008 194943X008 181847 85179 179148X479 192126 182466 187622 194941 179139 194940 189282 174697 179830 193885 192093X421 700279 12000045 146315 Wheel Assembly, 16", Power Steering, LH Pin, Klik 1/4 Cover, Power Steering Screw, Hex Head #10-24 x 1/2 Capscrew, Hex Head, Flanged 3/8-16 x 1 Bracket, Steering Cable, RH Bracket, Steering Cable, LH Screw, Hex Head 1/4-20 x 3/8 Screw, Hex Head 5/16-18 x 1/2 Link, Steering Lever Yoke, Steering Pin, Steering Lever Bellcrank Bracket, LH Steering Bracket, RH Steering Pin, Steering Bellcrank Retainer, Hairpin Bracket, Steering Driver, Wheel Ring, Wire Retainer Lobe, Wheel Slide, Clutch Spring, Clutch Slide Lobe, Axle Key, Square 1/4 x . 875 Washer, Thrust (1") Bearing, Axle Spring, Return, Steering Latch Wheel Assembly, 16", Power Steering, RH Clip, Retainer Ring, Retaining Screw, Hex Head, Tapping 5/16-18 x 5/8 KEY PART NO. [. . . ]