User manual PORT DESIGNS MANHATTAN BF CLAMSHELL BROCHURE

[. . . ] Go to " Will Not Unlock" Troubleshooting Section. 2 LO 2 3 nF 3 When the filling Continues for Go to " No Water Fill" more than 40 minutes or there is no Troubleshooting Section. Go to " Will Not Lock" Troubleshooting Section. 4 FL 4 5 LE 8 A water level lower than the Reset water level (25. 6Khz) is detected for Go to "No Water Fill" 5 seconds during the Wash/Rinse Troubleshooting Section. (When the input signal from the water level Go to "No Water Fill" sensor is out of range, the unit will Troubleshooting Section send out beeping sounds and halts the cycle. ) A fault is detected in the water level sensor. Data (frequency) shows the water level is at or above the First check to see that all of water overflow water level. [. . . ] If the Start/Pause button is pressed during Quick Spin Test Mode, it will stop accelerating and hold its spinning speed for 10 minutes before going back to Quick Spin Test Mode. Also, to cancel the hold and allow Quick Spin Test Mode to continue, press the Dealy Start and Pre Wash Keys together for 3 seconds. If you hold down the Dealy Start and Pre Wash keys for three (3) seconds when the washing machine is not in Hold Speed Mode, Quick Spin Mode is exited and Service Mode is restored. ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. Cycle Count Check Mode Service Mode Signal Cycle Count Definition of Cycle Count Check Mode: - Cycle Count Check Mode is to tally up the number of washings. How to Enter: - To enter the Cycle Count Check Mode, press the Signal Key during Service Mode. When the Signal key is pressed, the total number of washings will light up and a signal LED will glow. (For normal and Continuous Run cycles, the count is carried out at the end of the cycles. To exit the Cycle Count Check Mode, press the "Signal" key again. S/W Version Check Mode Definition of S/W Version Check Mode: Service Mode Soil Level S/W Version Check Mode - S/W Version Check Mode is to bring up S/W Version information. How to Enter: - To enter the S/W Version Check Mode, press the Soil Level Key during Service Mode. Press the Soil Level Key to bring up its software Version EX) Generate AE49 at Version 49 (AE is Micom code, 49 is it's software version) . To exit the S/W Version Check Mode, press the Soil Level S/W once again. Then, it returns to the Service Mode with motor RPM illuminating. ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. Fast Time Down Test Mode Service Mode Temp. - If the Start/Pause button is pressed during an LED mode operation, "- - - -" is displayed on the 7 segment display and the initial Demo mode is entered. TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. TROUBLE DIAGNOSIS - As the micom wash machine is configured of the complicate structure, there might be the service call. Below information is prepared for exact trouble diagnosis and suitable repair guide. Caution for the Repair and Replacement Please follow below instruction for the trouble diagnosis and parts replacement. ) As some electronic components are damaged by the charged static electricity from the resin part of machine or the human body, prepare the human body earth or remove the potential difference of the human body and machine by contacting the power supply plug when the work contacting to PCB is executed. ) Since AC120V is applied to the triac T1 and T2 on P. C. B, the electric shock may occur by touching and be careful that the strong and weak electricity are mixed. ) As the P. C. B assembly is designed for no trouble, do not replace the P. C. B assembly by the wrong diagnosis and follow the procedure of the trouble diagnosis when the micom is not operated normally. TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. TROUBLE DIAGNOSIS Will Not Start · Plug the unit into the wall outlet. · Push any key to turn on the washer and press the Start/Pause key to run the washer. (If the washer is in suds period, Suds will light up instead of remaining time. ) · Check for restricted drain system. (If there is electrical problem in drain system, "nd" error will occur after 15 minutes. ) · Check Water Supply. Be sure the standpipe is capable of accepting the flow of water from the washer. · Make sure end of drain hose is correctly inserted and secured to drain standpipe. [. . . ] (Refer to PCB Connector Check. ) · Try Door Lock and check for 120V to Door Lock Connector. If 120V present, change Main Control Board and if not, change Door Lock switch. Will Not Unlock · Check if the door is being pushed out, which may keep it from unlocking. If "LO" keeps illuminating, check PCB and Door Lock Switch. TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. TROUBLE DIAGNOSIS · Read Lock Switch and PCB (CN2 & CN3). [. . . ]