User manual POLYCOM SPECTRALINK 8020 ADMINISTRATION GUIDE FOR SIP VERSION M

[. . . ] New Software Version Requirements See page 41 and Appendix D SpectraLink 8020/8030 Wireless Telephone Administration Guide Session Initiation Protocol (SIP) December 2010 Edition 1725-36038-001 Version M SpectraLink 8020/8030 Wireless Telephone: Administration Guide for SIP Patent Information The accompanying product is protected by one or more US and foreign patents and/or pending patent applications held by Polycom, Inc. Notice Polycom, Inc. has prepared this document for use by Polycom personnel and customers. The drawings and specifications contained herein are the property of Polycom and shall be neither reproduced in whole or in part without the prior written approval of Polycom, nor be implied to grant any license to make, use, or sell equipment manufactured in accordance herewith. Polycom reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Polycom to determine whether any such changes have been made. [. . . ] The line icons 1-9 display and count down as the handset steps through this sequence. If there is difficulty at any step that prevents initialization from continuing, an error message will display and the related icon(s) will stay on. Please see the error table at the back of this document for instructions on how to handle error messages that occur during initialization. Icon 123456789 12345678 1234567 The icon(s) shown in bold turns off when: The handset has located and authenticated and associated with at least one AP, and is proceeding to bring up higher-layer networking functions. The handset is either configured for Static IP, or if configured for DHCP, the DHCP discovery process has started. If DHCP is configured, a DHCP response was received which contains a good DNS server configuration. Note: Used for SVP QoS only and not present when using Wi-Fi Standard QoS or CCXv4. SVP Server address found via DNS lookup 12345 All networking functions are complete (notably, DHCP), and the handset is proceeding with establishing the SRP link to the SpectraLink 8000 SVP Server. 123456 PN: 1725-36038-001-M. doc 79 SpectraLink 8020/8030 Wireless Telephone: Administration Guide for SIP Icon 1234 The icon(s) shown in bold turns off when: Note: Used for SVP QoS only and not present when using Wi-Fi Standard QoS or CCXv4. The SRP link is established; all network stack initialization is complete, proceeding with application-specific initialization. 123 12 (no icons) Registering (no icons) EXT. Icon 2 is extinguished if a handset specific SIP config file is found. Handset is attempting to register each of the specified line contacts. Handset has registered with at least one contact on one proxy server. The line one contact is displayed. During the last three steps of this process, the handset contacts the SIP TFTP server and downloads general information about the proxy server(s), downloads specific information pertaining to the handset, registers with the proxy server(s), and verifies handset credentials. If the username and password have not been defined in the Admin menu, you will be prompted to enter both of these items before the extension number can display. The user name must correspond to the configuration file that contains user-specific information. If the file is not found, an error message will appear and the handset will restart. See Chapter 5 Programming the SIP Handset Features, section SIP TFTP Server Configuration Files. Handset Modes Standby mode (on-hook) In standby mode, the handset is waiting for an incoming call or for the user to place an outgoing call. The extension number is shown on the display and there is no dial tone. In this mode, the handset is conserving battery power and wireless LAN bandwidth. When an incoming call arrives, the handset rings; the handset enters the active mode and remains so until the call is ended. The call is 80 PN: 1725-36038-001-M. doc Using the SIP Handset answered by pressing the START key or the Answ or Spkr softkey. The handset will ring according to user preference as specified in the standby menus. If you do not wish to accept the call, some SIP call servers support the ability to press the Rej softkey. If supported, the SIP call server will redirect the call as configured by the system administrator. Active mode (off-hook) The handset is in the active mode when an incoming call is answered or when it is in communication with the SIP server without being in an active call. [. . . ] FAVORITE = 3001; User Name 1 #FAVORITE = 3002; User Name 2 #FAVORITE = 3003; User Name 3 #FAVORITE = 3004; User Name 4 #FAVORITE = 93035551212; User Name 5 Cell #FAVORITE = 3006; User Name 6 #FAVORITE = 3007; User Name 7 #FAVORITE = 3008; User Name 8 #FAVORITE = 3009; User Name 9 #FAVORITE = 3010; User Name 10 #FAVORITE = 3011; User Name 11 #FAVORITE = 3013; User Name 12 #FAVORITE = 3013; User Name 13 #FAVORITE = 3014; User Name 14 #FAVORITE = 3015; User Name 15 # # Favorites can also be configured to prompt users to enter more digits. # In the below example if the Feature Access Code for call forwarding is #21 # When the user selects the Favorites option and then Call Forward they would # see "Call Forward Enter Destination:" # They would then have a chance to enter the fwd destination before pressing the send key #FAVORITE = #21<Enter Destination:>; "Call Forward" # In the example below the user would be prompted "Call Pickup Pickup Number: # to enter a call pickup number # for a call pickup Feature Access Code starting with *5 #FAVORITE = *5<Pickup Number:>; "Call Pickup" 144 PN: 1725-36038-001-M. doc 15 Appendix D: Minimum Software Requirements for Rev C Handsets Recent hardware changes affect the Polycom SpectraLink 8020/8030 Wireless Telephones. The affected products can be identified by a "Rev C" on the label. The changes require the minimal software version 131. 029 to run on the handset. [. . . ]