User manual POLYCOM RMX 1500 HARDWARE GUIDE VERSION V7.0.2

[. . . ] 1-1 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 RMX 1500 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 RMX 1500 System Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Conferencing Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The power cord should only be connected to a power outlet that has a protective ground contact. Ensure that the power cord is easily accessible from the back of the system at all times. Place the equipment in a well-ventilated area where the vents are free from obstruction. Do not use liquids around your equipment. · · · · · · · · · Rack Mount Safety Precautions The following precautions should be followed with regards to rack mount safety: · · Keep the area around the RMX 1500 clean and free of clutter. Decide on a suitable location for the equipment rack that will hold the RMX 1500 unit. It should be situated in a clean, dust-free area that is well ventilated. Avoid areas where heat, electrical noise and electromagnetic fields are generated. Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor with the full weight of the rack resting on them. · 1-6 Polycom RMX 1500 Hardware Guide · · · · · · · · In a single rack installation, stabilizers should be attached to the rack. Always make sure the rack is stable before extending a component from the rack. You should extend only one component at a time - extending two or more simultaneously may cause the rack to become unstable. Before you install the rails, determine the placement of each component in the rack. Install the heaviest components on the bottom of the rack first, and then work up. Always keep the rack's trays and card's slots closed when not servicing, to maintain proper cooling. Installation Precautions When handling electronic components, standard anti-static precautions must be observed: · Wear a grounding strap · · Handle cards by their edges only and do not touch their components or connector pins Keep components in anti-static bags, when not installed in the RMX1500 The following precautions should be followed with regards to installation of the RMX 1500: · Use a regulating uninterruptable power supply (UPS) to protect the RMX 1500 from power surges and voltage spikes, to keep your MCU operating in case of a power failure. Place the RMX 1500 on a hard, flat surface such as a desktop or mount it on 19" rack. Be sure that the areas in the left and right side of the system are clear for proper ventilation. Sealed System!The RMX 1500 is a sealed system, breaking the seal and opening the RMX chassis VOIDS the WARRANTY! · · 1-7 Chapter 1-Hardware Description Installing the RMX 1500 For detailed instructions, precautions and requirements for installing the RMX 1500 refer to the Polycom RMX 1500 Hardware Guide. The following procedures have to be performed to install the RMX 1500 in your site: · · · · Unpacking the RMX 1500 Installing the RMX in a rack or as a standalone Connecting the RMX 1500 to the power source Connecting the network (LAN, IP and ISDN) cables to the RMX. Unpacking the RMX 1500 To unpack and lift the RMX 1500: 1 When you receive the RMX 1500 packing case, inspect the equipment for damage and verify that the components match the packing slip. Two boxes are placed on the top Stratocell®, labelled: -- Installation Accessories. This kit contains the accessories for the 19"/23" racks as follows: Write down the RMX's serial number that is on a sticker on the back of the unit. Table 1-5 Item ID MEC2791A-L0 19" & 23" Rack Installation Accessories Package Description Chassis runners (60cm in length) suitable for installation within 60cm of inter spaces (front-to-rear stands). Do not use an Extension cord with the cable. · 1 Make sure that the power button is switched OFF on the RMX 1500. ON/OFF button USB Slot 2 Insert the power cable into the power connector on the rear panel of the RMX 1500. 1-11 Chapter 1-Hardware Description Connecting Cables to the RMX 1500 To connect the cables: · For the RTM-IP 1500 module: -- Connect the Media cable to LAN 2 port. -- Connect the Network cables to the MNG (Signaling) port & MNGB (Management Network) port. · For the RTM ISDN 1500 module: -- Connect the E1/T1 cables to their PRI (1-4) ports. Power Cable E1/T1 PRI Connection(s) LAN 2; media, MNG; signaling, MNGB; management & Shelf Figure 1-1 RMX 1500 Rear Panel View with AC Power and Communication Cables The LAN 1, LAN3, LAN4 and Modem ports are not be used and the plastic caps covering those ports should not be removed. First-time Power-up 1 For first entry installation, you must insert the USB key containing the modified IP addresses in USB slot on the RMX's front panel. [. . . ] Slide in the RTM ISDN 1500 card. 4 Insert the card into the slot and tighten the captive screws on each side of the rear panel of the card, securing the RTM ISDN card to RMX. 2-2 Polycom RMX 1500 Hardware Guide 5 Connect the PRI cables. 4 E1/T1 connections 6 7 Turn ON the RMX 1500. For more information see, RMX 1500/2000/ Getting Started Guide, Chapter 2, "Procedure 2: Product Registration" on page 2-20. For more information see, RMX 1500/2000/4000 Administrator's Guide, Chapter 13, "Adding/Modifying ISDN/PSTN Network Services" on page 13-51. b 2-3 Chapter 2- Component Installation & Replacement Component Replacement The RMX 1500 is designed with ease of maintenance in mind. Most components are swappable and are accessible directly via the front panel or the rear panel. [. . . ]