User manual POLYCOM PREMIER CART INSTALL A COLLABORATION SYSTEM

[. . . ] Avoid tipping - The Premier Cart has been tested, and IEC 950 and UL-approved, for Polycom-approved 27- and 32-inch monitors (29- and 34-inch monitors for Europe). If you use other monitors, you must ensure that the Premier Cart cannot tip. Monitor Size - Do not install a monitor larger than 32-inch (34inch in Europe) on the Premier Cart, or it may tip over. Power cables and polarity - Use power cables and adapters supplied by Polycom. [. . . ] To install the monitor, you need back brackets and Velcro® straps, which secure the monitor to the Premier Cart. You also need a front bracket, which is shipped in its own box with the collaboration system. The front bracket you receive is the appropriate size for your monitor. Note: These steps are for installing the 27-inch (29-inch in Europe) or 32-inch (34-inch in Europe) monitor that comes standard with the Premier Cart. 9 INSTALLING A COLLABORATION SYSTEM ON THE PREMIER CART Installing the Front Bracket on the Monitor To install the front bracket on the cart: 1. Place the bracket on the Premier Cart so that the clamps on the bracket align with the cutouts on the top of the cart a . Pull the bracket forward until the hole for the screw on the bracket aligns with the hole in the cart b . Use a Phillips screwdriver and the screw provided to secure the bracket to the top of the Premier Cart. b a a Installing the Back Brackets for the 27-inch (29-inch in Europe) Monitor Before you begin, note that you must follow these instructions exactly to ensure that the monitor is installed safely. Warning If the brackets are not correctly installed, the straps won't hold the monitor securely in place. The monitor could work free of the front bracket, and tip. 10 Installing the Monitor To install the back brackets for the 27-inch (29-inch in Europe) monitor: 1. Determine which size monitor you have. If you have a 32-inch (34-inch in Europe) monitor, go to the "Installing the Back Brackets for the 32-inch (34-inch in Europe) Monitor" section on page 12. 2. Position the Velcro straps a on top of the cart, as shown, with the loop side of the Velcro facing up. You don't need to separate the loop side from the hook side. 3. Place the brackets on top of the straps, aligning the holes in the brackets with the holes in the Velcro straps and the holes in the grooves b on the cart. Make sure that the loose ends of the straps extend beyond the rear of the Premier Cart. The two holes in the brackets must be aligned with the 5th and 7th holes counting from the back of the cart (the brackets will cover the 6th hole). 4. Insert the screws through the brackets and straps and into the Premier Cart. Tighten the screws. To continue the installation of your monitor, go to page 13, "Positioning the Monitor on the Premier Cart. " b a 11 INSTALLING A COLLABORATION SYSTEM ON THE PREMIER CART Installing the Back Brackets for the 32-inch (34-inch in Europe) Monitor Before you begin, note that you must follow these instructions exactly to ensure that the monitor is installed safely. Warning If the brackets are not correctly installed, the straps won't hold the monitor securely in place. The monitor could work free of the front bracket, and tip. To install the back brackets for the 32-inch (34-inch in Europe) monitor: 1. Position the Velcro straps a on top of the cart, as shown, with the loop side of the Velcro facing up. You don't need to separate the loop side from the hook side. 2. Place the brackets on top of the straps, aligning the holes in the brackets with the holes in the Velcro straps and the holes in the grooves b on the cart. Make sure that the loose ends of the straps extend beyond the rear of the Premier Cart. The two holes in the brackets must be aligned with the 3rd and 5th holes counting from the back of the cart (the brackets will cover the 4th hole). 3. [. . . ] Once you have set up your camera, refer to this section for information on connecting audio and power cables to the Premier Cart. Note: If your collaboration system was shipped with two monitors, see the iPower 900 Series Collaboration System Administrator's Guide for instructions on installing cables with dual-monitors systems. Connecting the Audio Cables The Premier Cart contains a Bose® speaker with a pre-installed audio power cable. At the back of the collaboration system, plug the orange end of the audio output cable into the orange LINE OUT connector a on the computer box. The audio output cable came packaged with the iPower 970 or iPower 960 Collaboration System. 2. Plug the white end of the audio output cable into the single end of the black Y-adapter cable b . The black Y-adapter cable came packaged with the iPower 80 camera. 15 INSTALLING A COLLABORATION SYSTEM ON THE PREMIER CART 3. [. . . ]