User manual POLYCOM KIRK WIRELESS SERVER 8000 CONFIGURATION GUIDE V2.5

[. . . ] Polycom® KIRK® Wireless Server 8000 & KIRK® Wireless Server 2500 Configuration Guide Version 2. 5 | October 1, 2010 | 14184631 Copyright © Polycom, Inc. All Rights Reserved Proprietary and Confidential The information contained herein is the sole intellectual property of Polycom, Inc. No distribution, reproduction or unauthorized use of these materials is permitted without the expressed written consent of Polycom, Inc. Information contained herein is subject to change without notice and does not represent commitment of any type on the part of Polycom, Inc. [. . . ] If set to "Odd" then the base station will use an odd time slot (1, 3, 5, 7, 9, 11). If set to "Follow RPN", the base station will use even time slots if it has an even RPN; if it has an odd RPN then the base station will use odd time slots. (0-255) For more information, see "Radio Part Numbers" on page 52 The time it takes the signal to reach the base station. (1-8) The following information is available Parameter RFP PCS Part Number Region Time slot in air RPN Cable Delay Shelf Card No. To Change Base Station Region 1 2 On the Base Station tab, right-click in any cell in the row that contains the base station (RFP) whose region you want to change. a b c d Europe South America Taiwan USA Important You should only change to a region with a frequency range that is legal for use in your area. Polycom, Inc. 51 Polycom KIRK Wireless Server 8000 & KIRK Wireless Server 2500 Configuration Guide Base Station Settings 3 Click the Write button, to write the changes to the system. To Change Base Station Slot 1 2 On the Base Station tab, right-click in any cell in the row that contains the base station (RFP) whose slot you want to change. a b c 3 Even Odd Follow RPN Click the Write button, to write the changes to the system. To write Region or Slot to a single Base Station 1 2 On the Base Station tab, right-click in any cell in the row that contains the base station (RFP) whose slot or region you have changed. Click Write Region/Slot to Single RFP. To Reset a Single Base Station 1 2 On the Base Station tab, right-click in any cell in the row that contains the base station (RFP) that you want to reset. Click Reset Single RFP. To Change Region on All Base Stations (RFPs) 1 2 On the Base Station tab, right-click in any cell. Click Change All RFPs to <region>/Follow RFP. Radio Part Numbers Base stations and repeaters both transmit a radio part number - an 8 bit number between 0 and 255. The handset compares the RPN of the base/repeater to which it is currently connected to that of the RPN of the base station/repeater it wants to handover to. The type of handover to use depends on the units involved in the handover. Handovers · Handovers between two base stations must take place as connection handovers. 52 Polycom, Inc. Base Station Settings System Management · Handovers between a repeater and the base station with which the repeater is synchronized should preferably take place as bearer handovers, because this is the fastest process. Handovers between a repeater and a base station with which the repeater is not synchronized must take place as connection handovers. · Handover Capabilities A handset cannot tell the difference between a base station and a repeater. Therefore, the RPN transmission pattern by default determines how the handover takes place. Polycom Kirk base stations transmit a pattern that determines whether to use a connection or a bearer handover. By default the base stations are configured to perform a bearer handover if there is a difference of 64, 128, or 192 between the two RPNs. In systems with more than 64 base stations you must be careful when you reuse RPNs. That is, base stations that are mounted in close proximity of each other can not have a difference in RPN of 64, 128, or 192. The handset will not be able to make a connection handover as shown in Figure 7-7 on page 53. Figure 7-7 RPN and Handovers Handover fails Base station RPN 4 Base station RPN 68 Handover succeeds Repeater RPN 132 Also, a handset must never be able to detect two radio units (base stations or repeaters) with the same RPN at the same time. If an RPN is reused, the units must be placed at a fair distance from each other. Recommended Numbering Pattern, if you absolutely have to use repeaters Go to "Base Station and Repeater Numbering" on page 74 to see a complete list of the recommended repeater and base station numbering in systems with up to 512 base stations. Polycom, Inc. 53 Polycom KIRK Wireless Server 8000 & KIRK Wireless Server 2500 Configuration Guide MSF Messages (Message Service Function) MSF Messages (Message Service Function) From the MSF Demo tab you can send text messages to any MSF compatible handset connected to the KWS 8000 or KWS2500. Also, any MSF-compatible handset connected to the KWS 8000 or KWS2500 can send text messages to the KWS 8000 or KWS2500. Note The MSF Demo tab is only a demo of messaging services that demonstrates the capacity of the messaging API. The API is intended to be used by a third-party application, such as an alarm server. [. . . ] The United Nations Convention on Contracts for the International Sale of Goods (1980) is hereby excluded in its entirety from application to this Agreement. This Agreement represents the complete agreement concerning this license and may amended only by a writing executed by both parties. If any provision of this Agreement is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. If you have any questions concerning this Agreement, or if you desire to contact POLYCOM for any reason, please contact the POLYCOM office serving your country. [. . . ]