User manual POLYCOM EF200

[. . . ] ECHOFREETM EF200 PHONE ADD USER MANUAL Copyright © 1999 ASPI Digital. Because of technical progress, specifications are subject to change without notice. EchoFree is a trademark and ASPI is a registered trademark of ASPI Digital. ASPI Digital - The Sound of DSP 1720 Peachtree Street NW, Suite 220 Atlanta, GA 30309-2439 (404) 892-3200 www. echofree. com Technical Support: (404) 892-3200 help@aspi. com EF200UM-0100-99 EF200 USER MANUAL Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Preparing for Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This is the same Device ID that is set by the rear panel DIP switches on the EF200. The Device ID must always have two digits, so if the ID is less than ten, a leading zero is needed. Each EF200 in a system should have a different Device ID, so they can each be addressed individually. It's ok for an EF200 to have the same Device ID as a different ASPI Digital product, because they will be differentiated by the device type. On the EF200, the Device ID can be a 2 digit number from 00 to 31 26 Copyright © 1998, All Rights Reserved EF200 COMMAND SET REFERENCE Command name The command name is a unique string of characters that indicates which command the EF200 should execute. Command names for different products are not necessarily the same, since the function and features of each product are different. A list of available EF200 command names is shown in Table 4 on page 28. Command data The command data is a string of up to 32 ASCII characters which follows the command name. The allowed content of the command data depends on which command is being used. Usually, this is only one character because most commands just turn a feature on or off. For instance, the DIAL command may be given an entire phone number at once. Also, some messages from the EF200, such as caller ID information, may have several characters. Sending commands to multiple devices Commands can be sent to multiple devices by replacing the device type or Device ID characters with the `*', character. Example The following example commands illustrate the different ways you can send commands to multiple devices by replacing the device type and/or Device ID with `*' characters. Dial directory assistance on all EF200s (don't try this at home, kids). Request software version of all devices of all types. ASPI Digital - The Sound of DSP 27 EF200 USER MANUAL VALID COMMANDS AND MESSAGES The following table is a list of commands recognized by the EF200. Table 4: EF200 Command List Command AA ACKMOD AGC AH CALLP CID DIAL DTMF DTMFC ERROR FLASH GAINA GAINP HOLD LEC LOCKFP MUTEP MUTER NS NSL PHONE PING PRIVACY REMCON RESETF RESTNV RING SAVENV SOUNDL, SOUNDP SWVER TONEE TONER Meaning enable/disable auto answer mode enable/disable acknowledgment mode enable/disable automatic gain control enable/disable auto hangup mode enable/disable call progress messages enable/disable caller ID dial one or more digits enable/disable DTMF detection enable/disable DTMF clamping enable/disable error messages send hook flash signal on phone line set phone input gain set phone output gain put phone on hold without disconnecting enable/disable line echo cancellation lock front panel (disables front panel buttons) mute/unmute phone output mute/unmute remote output enable/disable noise suppression set noise suppression level connect/disconnect phone see what devices are connected to the remote controller privacy mode (mute all output audio) remote connect/disconnect restore settings to factory defaults restore settings from non-volatile memory enable/disable ring messages save current settings to non-volatile memory send a tone to the AEC and remote ends, or to the phone request software version enable/disable entry and exit tones enable/disable ring count Page 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 60 61 62 28 Copyright © 1998, All Rights Reserved EF200 COMMAND SET REFERENCE The following table is a list of messages sent by the EF200 to the host. Table 5: EF200 Message List Message CALLP# CIDT CIDN CID# CIDX DTMF# ERROR# PONG RING!Meaning call progress tone detected caller ID timestamp caller ID name caller ID phone number caller ID not detected DTMF tone detected error condition occurred device response to PING command incoming ring detected Page 63 64 64 64 64 65 66 67 68 ASPI Digital - The Sound of DSP 29 EF200 USER MANUAL AA - ENABLE/DISABLE AUTO ANSWER MODE When auto answer mode is enabled, the EF200 automatically picks up the phone after the second ring. When the call is finished, auto answer remains enabled and the EF200 will automatically answer the next call. If auto answer mode is disabled, the PHONE command should be used to answer the call manually. The factory default setting for AA is 0 (off). Remote Commands The following commands can be sent by the remote control device to enable or disable auto answer. Request status of auto answer. EF200 Messages The following messages are sent by the EF200 in response to an AA?command, or in response to any AA command when acknowledgment mode is on. Auto answer is currently on. Example In the following example, the remote control device requests the auto answer status of the EF200 with Device ID number 12. [. . . ] The errors are numbered, and the meaning of each error number is described below. Error messages are enabled or disabled with the ERROR command. Remote Commands The ERROR# command should not be sent to the EF200. It's only used as a message from the EF200. EF200 Messages The following messages are sent by the EF200 when it has an error. Invalid command data. Example In the following example, the remote control device tries to send a few invalid commands to the EF200 with Device ID 6. [. . . ]