User manual POLTI VAPORETTO 2085

[. . . ] ® VAPORETTO 2085 A G B 5 3 2A 1 C 2 D E F 9 6 4 11 9 12 11 H 11 13 9 8 10 22 7 11 14 15 11 16 11 24 17 20 11 21 23 V U R S Q 18 11 19 T 5 6 4 Fig. 5 ON OFF VT 2085- M0S07125 - Ed. 1O03 2 VAPORETTO 2085 Read these instructions carefully before using the appliance. PRECAUTIONS KEEP THESE INSTRUCTIONS · Read these instructions for use carefully before using the appliance. · Any use which does not comply with these instructions will invalidate the warranty. · The wiring system to which the appliance is connected must always comply with the laws in force. [. . . ] However, as water by its nature contains limestone, which may cause a build-up of limescale in the boiler, in hard water areas we recommend the use of our naturalbase decalcifier KALSTOP FP 2003. Ensure the patented safety cap (A) is fully and correctly screwed on, otherwise you may experience steam escaping from around the cap. Connect the power supply cable (F) into an earthed power supply of the correct voltage. WARNING: Do NOT under any circumstances put or leave the filler funnel in the water filling aperture of the appliance when the appliance is connected to the mains electricity supply. The first burst of steam may contain some water droplets, due to imperfect thermic stabilisation inside the flexible hose. We would therefore advise that the first jet of steam is played onto an old cloth until a constant pressure of steam is obtained. Note: The generator on/off switch (B) may go on and off from time to time during use of VAPORETTO. This indicates the machine is maintaining the correct and constant pressure and is quite normal. If the flexible hose is too much twisted during use, the NO-VOLT device stops the steam flow. CONNECTION OF THE ACCESSORIES All the accessories of VAPORETTO can be connected to the handle or to the extension tubes as follows (fig. Move the accessories locking button (11) on every accessory to the "OPEN" position. 3b. Move the accessories locking button (11) back to the "CLOSED" position. Check that the connector button has engaged and the accessory is fully connected. PAT E N T E D S A F E T Y C A P / '' WAT E R O U T '' The appliance is equipped with a safety cap, which prevents opening of the boiler as long as there is any pressure remaining inside. This is an important and indispensable safety device, and it is necessary to follow certain procedures when re-filling the boiler. Whenever you have used up all the water in the boiler, proceed as follows: 1c. Switch off the machine at the generator on/off switch (B) 2c. Press the steam request button (3) on the steam gun (2) or, if using the iron, the steam request button (R) on the iron (Q) so as to fully exhaust the steam supply from the boiler. 5c. Unscrew anti-clockwise the patented safety cap (A) 6c. Wait for a few minutes to allow the boiler to cool down. 7c. When cool, proceed to carefully refill the boiler as described in paragraph 1 of the section "Preparation for Use". If refilling the boiler when not completely cooled, we recommend that you carefully pour only very small quantities of water at ENGLISH INSTRUCTIONS FOR USE 1a. Press the generator on/off switch (B) and the accessories on/off switch (C) which will light up. Open the cover of the central connector block (D) and insert the connector assembly (4) pressing the connector button (5) taking care that the locking tab (6) is correctly positioned in the lockin aperture (E) on the block (Fig. The steam gun (2) is equipped with a safety switch (2A) which prevents the accidental start of the steam jet by children or people who do not know how to operate the appliance. [. . . ] The treatment can be repeated as frequently as you wish, with no damage whatsoever. Fold a cotton cloth over 2 or 3 times (according to the length and resistance of the pile) and fasten it onto the brush. Move the brush rapidly in all directions without applying any pressure. You should avoid lingering in the same place, as this may soak the area. [. . . ]