User manual POLTI VAPORELLA PRO 5200 R

[. . . ] · Before connecting Vaporella to the mains make sure that the current is the same as indicated for the machine and that the plug is an earthed plug. Water by its nature contains magnesium, mineral salts and other deposits which in hard water areas can contribute to limescale build up in the tank. To avoid these problems, it is necessary to swill out with tapwater and empty the generator tank after every 3 or 4 uses. In very hard water areas we recommend the use of our KALSTOP FP 2003, a special natural-base decalcifier which inhibits and breaks down limescale, making it easy to remove just by swilling out the tank with a little tapwater. [. . . ] It is necessary to keep the unit in horizontal position during operation. NO Vaporella Pro 5200 R ENGLISH I M P O R TA N T E I M P O RPA N TTA N T II MT O R TE N T E M POR A Before leaving our factory all our products are rigorously tested. For this reason your VAPORELLA, may contain a small quantity of remaining water in the tank. P R E PA R A Z I O N E P R E PA R AA I O N EO N E P R E PZ R A Z I P R E PA R AT I O N F O R U S E 1a. 1) and fill the boiler with about 1. 5 litres of water using the special funnel (13) making sure that it does not overflow (fig. However, as hard water by its nature contains limestone, which may cause a build-up of limescale in the tank, we recommend the use of a 50% tap water and 50% demineralised water. In hard water areas we recommend the use of our natural-base decalcifier KALSTOP FP 2003. Connect the power supply cable (9) into an earthed power supply of the correct voltage. Fig. 2 I NU T IRIILCZOO N S F O R U S E S U T UZIZ Z O T L TI UTILIZZO DRY IRONING 1b. Regulate the temperature of the iron by turning the knob (7) to the required temperature for the fabric shown on the knob itself. Set the iron temperature to the "COTTON - LINEN" steam position (fig. For steam ironing, all types of fabric can be ironed at this temperature. Wait for the steam pressure indicator light (5) and the "iron heating" indicator light (3) to switch off (about 15 minutes). Push button (10) on the iron to release bursts of steam from the holes on the soleplate. NOTE: during initial operation of the iron, a few drops of water mixed with steam may come out of the soleplate until the temperature stabilises. It is advisable to direct the first jets of steam onto an old cloth until a uniform stable jet of steam is obtained. Fig. By turning the steam flow control knob (6) you can vary P R E Paccording to E the amount of steam A R A Z I O Nthe type of textile to be ironed (more or less delicate). You can use this control to increase the steam flow by turning in clockwise direction. Turning the control in an anti-clockwise direction reduces the steam flow (fig. We suggest the maximum emission for heavy textiles like jeans, medium for cotton and linen, minimum for light textiles. TA P P O D I S I C U R E Z Z A / M A N C A N Z A A C Q U A PAT E N T E D S A F E T Y C A P / " WAT E R O U T " All Polti machines are equipped with the unique Polti patented safety cap, which prevents opening of the generator tank as long as there is any pressure remaining inside the tank. This is an important and indispensable safety device, and it is necessary to follow certain procedures when re-filling the tank. Lack of water is indicated by the (4) indicator light, which changes from constant to flashing. UTILIZZO When you have used up all the water in the tank, do as follows: 1a. Press the steam request button on the iron (10) so as to fully exhaust the steam supply from the tank. [. . . ] · Polti declines liability for any damage or accident derived from any use of Vaporella which is not in conformity with the instructions contained in this booklet. ENGLISH Vaporella Pro 5200 R FOR YOUR OWN SAFETY READ FOLLOWING INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO CONNECT THIS UNIT TO THE MAINS. M A I N S ( A C ) O P E R AT I O N ( o n l y U . This appliance may be fitted with a non rewirable plug, if it is necessary to change the fuse in a non rewirable plug the fuse cover must be refitted. If the fuse cover is lost or damaged, the plug must not be used until a replacement, available from the appliance manufacturer, is obtained. It is important that the colour of the replacement fuse cover corresponds with the colour marking on the base of the plug. [. . . ]