User manual POLTI VAPORELLA INOX 1000

[. . . ] Water by its nature contains magnesium, mineral salts and other deposits which in hard water areas can contribute to limescale build up in the tank. To avoid these problems, it is necessary to swill out with tapwater and empty the generator tank after every 3 or 4 uses. In very hard water areas we recommend the use of our KALSTOP FP 2003, a special natural-base decalcifier which inhibits and breaks down limescale, making it easy to remove just by swilling out the tank with a little tapwater. This is a preventive against scale build-up and protects the metal walls of the steam generator tank. KALSTOP is available from Polti dealers or by mailorder from your Polti Service Centre. [. . . ] Never direct the jet of steam towards small particles of debris without first protecting the user's eyes. Wait for the heater illuminated a switch (2) and the steam button (3) to go out. Push button (3) on the iron to release bursts of steam from the holes on the soleplate. If the heater illuminated switch (3) comes on during use, continue ironing as it is quite normal. NOTE: during initial operation of the iron, a few drops of water mixed with steam may come out of the soleplate until the temperature stabilises. It is advisable to direct the first jets of steam onto an old cloth until a uniform stable jet of steam is obtained. For dry ironing, connect the supply cable to the mains, push the iron on/off switch (4), regulate the temperature of the iron by turning the knob (1) to the required temperature for the fabric shown on the knob itself. · · · · · · · · PAT E N T E D S A F E T Y C A P / " WAT E R O U T " All Polti machines are equipped with the unique Polti patented safety cap, which prevents opening of the generator tank as long as there is any pressure remaining inside the tank. This is an important and indispensable safety device, and it is necessary to follow certain procedures when re-filling the tank. Press the steam request button on the iron (3) so as to fully exhaust the steam supply from the tank. When cool proceed to carefully refill the tank as described in paragraph 1a of the section "PREPARATION FOR USE" in the instructions. If refilling the generator when not completely cooled, we recommend that you carefully pour only very small quantities of water at each pouring into the tank, so as to avoid spitting from the tank. I M P O R TA N T Before leaving our factory all our products are rigorously tested. However, your VAPORELLA may contain some residual water in the boiler P R E PA R AT I O N F O R U S E 1a. Unscrew the patented safety cap (5) and fill the boiler with about 0. 8 litres of water using the special funnel (9) making sure that it does not overflow (fig. However, as hard water by its nature contains limestone, which may cause a build-up of limescale in the tank, in hard water areas we recommend the use of our natural-base decalcifier KALSTOP FP 2003. Connect the power supply cable into an earthed power supply of the correct voltage. Switch on the boiler and iron by pressing the switches (2) and (4) (fig. 2). I M P O R TA N T · · Do not leave the iron unattended whilst connected to the mains. Iron only on heat resistant surfaces and on surfaces that allow the steam to escape e. Set the iron temperature to the "COTTON - LINEN" 3 ENGLISH VA P O R E L L A I N O X 1 0 0 0 · Ensure the patented safety cap is fully and correctly screwed on, otherwise you may experience steam escaping from around the cap. The steam botton (3) may go on and off from time to time during use of Vaporella. [. . . ] However, as hard water by its nature contains limestone, which may cause a build-up of limescale in the tank, in hard water areas we recommend the use of our natural-base decalcifier KALSTOP FP 2003. Polti declines liability for any damage or accident derived from any use of Vaporella which is not in conformity with the instructions contained in this booklet. BLUE (Neutral) BROWN (Live) · · · FOR YOUR OWN SAFETY READ FOLLOWING INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO CONNECT THIS UNIT TO THE MAINS. M A I N S ( A C ) O P E R AT I O N ( o n l y U . Connecting it to other power sources may damage the unit. As the colours of the wires in the mains leads of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter "E" or by the earth symbol or green-andyellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter "N" or coloured black. [. . . ]