User manual POLTI MICHELANGELO INSTRUCTIIONS FOR USE

[. . . ] ® Michelangelo 3 4 5 6 7 8 9 2 1 10 11 12 21 17 16 18 19 15 14 22 Fig. A 13 20 25 12b b 12a 12c d AROMA MICHELANGELO - Edizione 1I06 26 Fig. C a 23 24 9 AROMA MICHELANGELO Dear Customer, Thank you for choosing this Polti product. With this coffee machine, you will enjoy full taste and aroma right from the first cup and make creamy cappuccino as well as tea and other hot drinks. [. . . ] IMPORTANT: The system must be programmed either for use of a water filter or for the hardness of the water and therefore the manual lime scale removal cycle. If you are using the filter on the machine and the system is programmed to "YES", water hardness and manual lime scale programming cannot be displayed. Follow the instructions in the section on "replacing the water filter" to replace it. Important: If you have not used the machine very much, you must replace the filter even if no indication appears on the display after a maximum of two months (see the section on "manual filter replacement (25)"). 7 Warning ­ scalding steam hazard: The steam is very hot!Residues left on the nozzle after frothing milk are hard to remove when dry, so it is a good idea to clean the whole assembly as soon as it cools down. Eliminate milk residues in the hole through which milk passes in the knob (12b) with a needle. Important: after using the steam wand, it is important to rinse the machine through before making coffee again to cool down the circuit, or the aroma of the coffee will be spoiled. Place a container under the coffee dispensing nozzle (8) and press the service button (7) or let a little hot water flow through the nozzle (12). PROGRAMMING Use the following buttons under the display for programming: P Programming mode > selection button ok confirmation button exit interrupt or conclude programming The machine allows you to set the following functions: 1. Statistics ENGLISH AROMA MICHELANGELO As a reminder, you may set the replacement date on the wheel on the top of the filter. For more thorough prevention of lime scale build-up, you should run the "lime scale removal" programme at least once a year even if you regularly use the resin-based filter. Without filter If you no longer want to use the filter, you must reprogramme the filter setting to "NO". This is important as you must use the lime scale removal programme if you are not using the filter. From this position you may continue programming or exit by pressing exit. Don't forget to programme water hardness when not using the filter. WATER HARDNESS The frequency of lime scale removal depends on the hardness of your local water supply. Set water hardness correctly as soon as you begin using the machine so that the system will be able to inform you when the lime scale procedure is necessary. First test the water using the litmus paper (26) supplied: Fill a small container with tap water. Dip the litmus paper into it and remove it immediately, then shake it gently. After about one minute you will be able to read the results by counting the red dots. Different levels are distributed as shown below: ­ ­ ­ ­ 1 red dot = 1 -7° dH / 1 - 12. 6°fH = LEVEL 1 2 red dots = 8 -14° dH / 12. 7 -25. 2°fH = LEVEL 2 3 red dots = 15-21° dH / 25. 3-37. 8°fH = LEVEL 3 4 red dots = > 21° dH / > 37. 8°fH = LEVEL 4 The factory setting corresponds to LEVEL 3. Press > again until the level of water hardness determined in the litmus paper test appears on the display. [. . . ] Clean the hot water and steam nozzle with a damp cloth after each use. IMPORTANT These wires in this mains lead are coloured in accordance with the following code. · Green-and-yellow: Earth · Brown: Live · Blue: Neutral FOR YOUR OWN SAFETY READ FOLLOWING INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO CONNECT THIS UNIT TO THE MAINS. As the colours of the wires in the mains leads of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter "E" or by the earth symbol or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter "N" or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter "L" or coloured red. M A I N S ( A C ) O P E R AT I O N This unit is designed to operate on 240V, 50 Hz current only. [. . . ]