User manual POLK AUDIO RM30

[. . . ] SPEAKER PLACEMENT CENTER CHANNEL SPEAKER (Figure 1) Place the center channel speaker as close to your TV as possible (Figure1). The most popular placement for the center channel speaker is right on top of your TV set. The small size and slender design of the RM7000 Series center channel speakers makes them easy to mount on the wall directly above your TV. RM7000 Satellites are magnetically shielded for safe placement on or near your TV. [. . . ] Make sure the material on which you plan to mount the speakers (plaster, drywall, paneling, stone, etc. ) can support the weight of the speakers (See product weight specifications on page 14). Make sure the locations you select do not conceal electrical wiring or plumbing. prior to installation , hold the speaker in the chosen location to make sure it safely clears obstacles such as ceiling , adjacent walls , corners , beams , lighting fixtures and door/window frames. Using the keyhole slots in the bracket template (included), mark the installation location of the keyhole slots with a pencil (Figure 10). Orient the template so that the small ends of the keyhole slots are facing "up" according to the direction of installation. If you are certain that there is a stud behind the wall surface, drive #10 screws (not included) through the wall and into the stud (Figure 11a). If there is no stud behind the wall at the chosen location, install #10 wall anchors (not supplied) into the wall by following the wall-anchor-manufacturer's instructions (Figure 11b). For masonry walls, use a masonry drill bit and #10 masonry anchor and screw (not included). Tighten screws into stud or wall anchors, leaving screw heads protruding 1/16" (1. Line up the keyhole slots on the bracket so that the screw heads pass through the large center hole of the slots. In the "On" position, the power amplifier will operate and the power light will glow GREEN until the switch is set to the "Off" position or the AC cord is disconnected from a power source. Turn it to "Off" if the system will not be used for extended periods of time, such as during vacations. R M 7 6 0 0 S U B W O O F E R L E V E L C O N T R O L (Volume) Subwoofer level (volume) is adjusted via the knob on the front of the subwoofer under the logo pod. This lets you adjust the level of bass easily after you have made the more complex adjustments on the rear of the Subwoofer. To set level, play a piece of music that has an average amount of bass content. " RM7600 SETTINGS On the back of the subwoofer (Figure 14), you will see the following controls: Variable crossover control Phase toggle switch +3dB bass boost switch High Pass Filter toggle switch (You will never need to change this out of the "0" position. ) The Subwoofer Level Control is found under the logo pod on the front of the subwoofer. It only effects signals that are sent through the low level, subwoofer and Speaker Wire inputs. It has no effect on signals fed into the LFE input (and you shouldn't be using that input anyway). R M 7 6 0 0 R E C O M M E N D E D S E T T I N G S -- O N W A L L & O F F W A L L (Figures 14, 15 & 15b) Mounting your right and left front satellites on the wall tends to increase their low-midrange response (the low range of a male voice). Mounting them on stands away from the sides of the room tends to decrease their low-midrange response. [. . . ] Allow at least 6" (15cm) between sub driver and wall or obstruction. To use Banana Plugs (US only): Carefully pry out the Binding Post Plugs (plastic plugs on the end of the binding posts) to expose Banana Plug holes. Use #10 screw for wall stud, use #10 wall anchors + screw for no wall stud. Use tornillos n° 10 cuando haya parales internos en la pared, use to rnillos y anclas n° 10 cuando no haya parales internos. [. . . ]