User manual POLK AUDIO LCI-IP

[. . . ] LCi-IP SERIES LC80i-IP LC265i-IP Active In-Wall/In-Ceiling Speakers Owner's Manual ENGLISH IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. [. . . ] For some requested measurements you may not be able to supply the requested information, and you may check the appropriate "skip question" box. When an "skip question" box is checked, no error message is displayed (figure 4). 6 Polk Audio Customer Service: 1-800-377-7655 (Outside US & Canada: 410-358-3600) Monday-Friday, 9:00 AM-6:00 PM EST, polkcs@polkaudio. com For more information visit our website at www. polkaudio. com 7 TROUBLESHOOTING Problem No audio Possible Reason(s) Audio signal is not connected to the speaker. Solution Make sure that the speaker is connected to the audio source using RCA cables or a RJ45 equipped Cat-5 cable. Make sure to use the Performance Optimization Wizard when connecting to an IP-based network, such as NetStreams' DigiLinX network. Also make sure to use any set-up software required for configuring the MRAV. Check the current hook-up configuration against the possibilities listed on page 5 to make any necessary adjustments. Once completed, make sure to press the RESET button on the CONTROL speaker, located on the speaker's front baffle. Make sure that the power cable is connected to both the power supply and the speaker and that the connectors are fully inserted on both ends. Make sure that the power supply is on and that there are no kinks in the power wire (i. e. Make sure to use any set-up software required for configuring the MRAV. Also make sure that the appropriate network decoder card has been installed into the CONTROL speaker if audio is coming to the speaker using the speaker's NETWORK connection. Set the CHANNEL switch to the opposite position and press the RESET button on the front baffle of the CONTROL speaker. Make sure that the cable connecting the speaker to the MRAV is sending the desired audio channel. Make sure that the RJ45 equipped Cat-5 cable has been tested for continuity. If you intend to use the USB connection for control, make sure it is plugged into the speaker and your computer. Make sure that the power cable is connected to both the power supply and the speaker and that the connectors are fully inserted on both ends. Check first to make sure the power supply's circuit's fuse is ON. Next, make sure that the power supply is on and that there are no kinks in the power wire (i. e. Also make sure that the power supply that is being used has a single-ended output. Check all wired connections and make sure that the audio signal cable is shielded properly. If it is not, either replace the cable or make sure that the cable is at least 6-inches away from any power cables as the frequency (50 or 60 Hz) of the AC power source will be audible at the speakers. While the EQ provides high performance in most situations, you are strongly encouraged to use the Performance Optimization Wizard. [. . . ] This Warranty applies only to Products purchased in Canada, the United States of America, its possessions, and U. S. The Warranty terms and conditions applicable to Products purchased in other countries are available from the Polk Audio Authorized Distributors in such countries. GARANTIE LIMITÉE La garantie de Polk Audio, Inc. , n'est valide que pour l'acheteur au détail original. La garantie sera automatiquement annulée avant sa date d'expiration spécifiée si l'acheteur original vend ou transfère le produit à tout autre parti. Polk Audio, Inc. , garantit - à l'acheteur au détail original seulement - que le ou les HAUT-PARLEUR(S), COMPOSANTE(S) DE FILTRE PASSIF et CAISSON(S) de ce produit Polk Audio seront exempts de tout défaut attribuable aux pièces d'origine et à la main d'oeuvre pour une période de cinq (5) ans à partir de la date de l'achat au détail original chez un revendeur agréé Polk Audio. [. . . ]