User manual POLK AUDIO GXR6

[. . . ] Check that you have the following parts: · · · · · · · 2 Speakers 8 Mounting clips 2 Grilles (GXR4, GXR5, GXR6 & GXR69) 8 Screws 1 Mounting template (Separate Sheet) Online registration card Mail-in registration card Installing car speakers is a serious project. If you have any doubts about your ability to execute any of the installation steps found in this manual, save yourself a lot of grief and contact a professional installer. If you intend to do the installation yourself we assume you possess some skill in the proper use of hand and power tools. No matter how much installation experience you have, we recommend that you. . . [. . . ] Draw the inside circle and mark at least two opposing screw locations. File the edges of any bare metal surfaces until smooth, then coat with primer to prevent rust. In the meantime, run wires from your amplifier or radio to the speaker locations. Hook the positive [+] wire to the wider of the two GXR terminals and the negative [­] to the narrower GXR terminal. Carefully align the speaker and beauty ring holes over the new screw holes and mounting clips. Tighten the screws firmly to secure the speaker to the mounting surface. 1 Template for description purposes only. SCREW HOLE TEMPLATE FIG. 2 Example of a typical mounting procedure. SCREW MOUNTING CLIP SPEAKER WIRES 4 Contact Polk Customer Service: 800-377-7655 polkcs@polkaudio. com For more info and accessories, visit www. polkaudio. com 5 GXR4 SPECIAL INSTRUCTIONS FOR IMPORT APPLICATIONS (TOYOTA/MITSUBISHI) LOW FREQUENCY CUT-OFF FOR SYSTEMS WITH SUBWOOFERS GXR4 models have flanges that can be removed to facilitate easy placement in tight spots, such as in some import vehicles (FIG. Remove only the flange(s) that are necessary to make the speaker fit the chosen location. In some vehicles, you may have to bend or angle (but not break) one of the two flanges to get the proper fit when installing the speakers in your dashboard. Do not use a sander or grinder, as that could cause fine metal shavings to fall into the voice coil and driver suspension units. If you have a subwoofer in your system, you may want to decrease the amount of bass frequencies going to your mid-range speakers (which is what your "full range" speakers would be if you had a subwoofer in your system). Doing this will result in better mid-range detail and increased power handling. There are two ways to roll off the bass before it gets to your mid-range speakers. One way is to use a "bass blocker, " a capacitor placed in series with the speaker input. Bass blockers are installed in series, one end connected with the positive lead from your amplifier and the other end connected to the positive lead of each of your speakers (FIG. Bass blocker capacitors (200 microfarad @ 100volts, non-polarized) are available at most car stereo dealers, RadioShack and parts supply stores. The other route is to use an electronic crossover device that allows filtering below 100Hz or so. You can find these devices at your authorized Polk Audio dealer. FIG. 4 Bass Blockers + Radio/Amp USE TIN SNIPS TO REMOVE FLANGES Bass blocker or capacitor + Speaker ­ ­ 6 Contact Polk Customer Service: 800-377-7655 polkcs@polkaudio. com For more info and accessories, visit www. polkaudio. com 7 AMPLIFIER POWER REQUIREMENTS GXR SERIES FULL RANGE SPECIFICATIONS Your new GXR Loudspeaker will work well with a variety of electronic components. As little as 10 watts per channel will deliver adequate listening levels in most cars. [. . . ] Please do not hesitate to contact us if you have questions about your speaker system. You will find additional information, informative articles, manual updates and cool stuff to buy that has "Polk Audio" all over it by visiting www. polkaudio. com. Mounting Depth (top) Mounting Depth (bottom) Peak Power Handling Continuous Power Handling Nominal Impedance Frequency Response Grille Height 2 5/8" (66. 7mm) 2 3/4" (69. 9mm) 125w 50w 2 1/4" (57. 2mm) 2 1/2" (63. 5mm) 125w 50w 4 ohms 50-21kHz 1 5/16" (33. 5mm) 6 15/16" x 9 13/16" (175mm x 249mm) 93dB 4 ohms 60-21kHz N/A 4 ohms 70-21kHz 7/8" (22mm) 6 3/4" (171. 5mm) 92dB 4 ohms 57-21kHz N/A Grille Diameter N/A N/A Sensitivity 92dB 92dB 8 Contact Polk Customer Service: 800-377-7655 polkcs@polkaudio. com For more info and accessories, visit www. polkaudio. com 9 GXR SERIES FULL RANGE SPECIFICATIONS GXR SERIES 1 YEAR WARRANTY Type GXR5 51/4" coaxial (133. 4mm) GXR46 4" X 6" coaxial (101. 6mm x 152. 4mm) 4" X 6" (101. 6mm x 152. 4mm) mid/woofer, 1/2" (13mm) PEI tweeter 3 3/4" x 6" (95. 3mm x 152. 4mm) 1 3/4" (44. 5mm) 2 1/16" (52. 4mm) 88w GXR4 4" coaxial (101. 6mm) Driver Complement 5 1/4" (133. 4mm) mid/woofer, 1/2" (13mm) PEI tweeter 4" (101. 6mm) mid/woofer, 1/2" (13mm) PEI tweeter Polk Audio, Inc. warrants the original purchaser only that this Polk Audio GXR Series Product (the Product) will be free from defects in materials and workmanship for a period of (1) one year from the date of original retail purchase from a Polk Audio Authorized Dealer. However, this warranty will automatically terminate prior to the expiration of the (1) one year period if the original retail purchaser sells or otherwise transfers the Product to any other party. The original retail purchaser shall herein after be referred to as "you. " To allow Polk Audio to offer the best possible warranty service, please fill out the Product Registration Card(s) and send them to the Factory at the address provided in the Registration Card within (10) ten days of the date of purchase. [. . . ]