User manual POLK AUDIO CSW200

[. . . ] The audio/video products may fall, causing serious injury to a child or adult, and serious damage to the products. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the appliances. Any mounting of the appliances should follow the manufacturer's instructions, and should use mounting accessories recommended by the manufacturer. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the appliances and to protect them from overheating, and these openings must not be blocked or covered. [. . . ] If you doubt that you possess the necessary skills or tools, consult your Polk Audio dealer or a professional installer. SPEX Cards configure the SWA500 for the particular model subwoofer you are installing. The card also has power control circuitry designed specifically to the subwoofer's requirements for extra reliability (see SWA500 instruction manual for installation instructions). cSW100 INSTALLATION PROCEDURE Protective Cover A 1/2" thick protective cover of MDF covers the CSW100 grille opening. This protective cover (3 1/4" x 13") is also the template you will use to cut the grille opening. Once installed, all you see is a tiny 2" x 12" grille (optional). Patented High Velocity Compression Drive® bandpass alignment with slot bass venting-- produces a gutsy, driving bass that other similarly sized built-ins can't equal. If you choose to use another grille, use one that doesn't resonate and caulk it. Taking the dimensions of the CSW enclosure, mark off the dimensions of the enclosure and then the center line dimensions of the woofer opening. Using the protective cover/template, mark off the grille opening you wish to cut. You will need to support a 33 pound subwoofer during the installation, so have a co-worker or mechanical device support the woofer during final installation. (Use the 3/4" screws supplied) Tighten both brackets on one side of the subwoofer until the brackets seat flush against the subwoofer. Attach additional anti-resonance pads (included) to any sides of the subwoofer that will mount flush against support beams. Place the subwoofer in the floor or ceiling space flush with the beam face, then attach the brackets to the beam, tightening them down completely. Extend the two loose brackets that attach to the other beam and tighten them flush against the beam. Direct Radiating Slot Port enclosure--produces a gutsy, driving bass that other similarly sized built-ins can't equal. THE SWA500 AMPLIFIER AND SPEX CARDS Note: When installing the Polk Audio SWA500 matching amplifier, make sure you install the appropriate SPEX Card. THE CSW155 CARTON INCLUDES: 1 Subwoofer 4 Mounting Brackets 16--3/4" Particle Board Panhead Screws 16 Washers 11 Isolation Pads (6 installed, 5 included) 1 Registration Card 1 Owner's Manual 1 Grille The CSW155 uses a 15 1/2" x 17 1/2" grille, which is included with the subwoofer. THE SWA500 AMPLIFIER AND SPEX CARDS Note: When installing the Polk Audio SWA500 matching amplifier, make sure you install the appropriate SPEX Card. SPEX Cards configure the SWA500 for the particular model subwoofer you are installing. The card also has power control circuitry designed specifically to the subwoofer's requirements for extra reliability (see SWA500 instruction manual for installation instructions). This protective cover (15 1/2" x 17 1/2") is also the template you will use to cut the grille opening. [. . . ] Some states do not allow limitation on how long an implied Warranty lasts, so the above limitations may not apply to you. This Warranty gives you specific legal rights, and you also may have other rights which vary from state to state. If this Product is defective in materials or workmanship as warranted above, your sole remedy shall be repair or replacement as provided above. This warranty does not cover service, parts, or supplies to repair damage to property other than the Product. [. . . ]