User manual POLK AUDIO ATRIUM 60

[. . . ] FIGURE 4 FIGURE 3 Place the speaker away from eaves and corners for less bass output. Do not reattach the speaker to the bracket until the bracket is mounted. Using spray paint, spray two thin coats of finish color with no primer [figure 8]. If you're using a compressor and spray gun, use the finest, most diffuse setting. [. . . ] If speaker wire is being fed from a hole in the wall behind the bracket, pull this speaker wire through the hole in the bracket before mounting the bracket [figure 11]. Line up the bracket, attached to the speaker, so that the screw heads pass through the large center hole of the bracket's keyhole slot. Let the speaker and bracket slide straight down, allowing the screw head to slip behind the smaller end of the keyhole slot [figure 12]. Tug gently on the speaker to make certain that the screws and bracket are properly aligned and that the wall anchors are secure. If the bracket is not held snug against the wall by the screw heads, remove the speaker from the wall, drive the screws in a little further and then remount the speaker. Once the speaker is mounted, the bracket knobs can be loosened to "aim" the speaker, and then hand-tightened to keep the speaker angled correctly [figure 14]. Si le fil de haut-parleur destiné à l'enceinte est passé dans le mur et sort derrière le support, passez le fil à travers le trou du support avant d'installer le support au mur [figure 11]. Product Disposal - Certain international, national and/or local laws and/or regulations may apply regarding the disposal of this product. For further detailed information, please contact the retailer where you purchased this product or the Polk Audio Importer/Distributor in your country. A listing of Polk Audio Importer/ Distributors can be found on the Polk Audio website www. Polk Audio loudspeakers and subwoofers are capable of playing at extremely high volume levels, which could cause serious or permanent hearing damage. Accepts no liability for hearing loss, bodily injury or property damage resulting from the misuse of its products. Keep these guidelines in mind and always use your own good judgment when controlling volume: · High volume in an automobile can hinder your ability to safely operate a vehicle. You are responsible for knowing the local laws governing acceptable mobile volume levels. FIGURE 11 Feed speaker wire from wall through bracket wire hole for easy mounting. FIGURE 12 Slide the bracket down on the screw heads to catch the keyhole slots. ALTERNATE SECURE MOUNTING For more solid mounting, screw the bracket directly into a weight-bearing stud on the mounting surface. Attach and remove the speaker from the permanently secured bracket by tightening and loosening the bracket knobs [as shown in figure 14]. NOTE: If placing your Atrium60 vertically on a surface, please attach 2 feet (included in accessary bag) to bottom of each speaker. MAKING THE CONNECTION For the best performance, use dedicated two-conductor, 16-gauge or thicker (descending number) audiophile-grade speaker wire, available at your authorized Polk Audio Dealer. Measure enough wire to reach from your amplifier or receiver to each speaker, plus an additional 12" to allow moving the speakers or equipment without having to disconnect the wires. Strip 1/2" of insulation from each of the two conductors on both ends of the wire length to expose the bare wire [figure 15]. [. . . ] Use the Power Port Plug for unprotected installation situations where the back of the speaker may get wet. 8 for salt and corrosion with PowerPort Plug Cabinet Material Mineral filled polypropylene Grille & Bracket Material powder coated aluminum Hardware Brass or stainless steel Terminals 1 pair Gold plated 5-way binding posts Woofer 1 6 1/2" (16. 8 for salt and corrosion» avec bouchon «Power Port Plug» Matériau du caisson Polypropylène à charge minérale Matériau de la grille et du support Aluminium enduit de poudre Quincaillerie Laiton ou acier inoxydable Bornes 1 paire de bornes «5 façons» plaquées or Woofer 1 61/2" (16, 5 cm) avec cône en polypropylène à charge minérale et suspension en butylcaoutchouc Tweeter 1" (25mm) à dôme métallisé avec structure magnétique en néodymium Hauteur x Largeur x Profondeur avec support et boutons 13 1/2" H x 7 11/16" L x 9 5/16" P (34, 2 cm H x 19, 5 cm L x 23, 6 cm P) Poids à l'expédition, la paire 26, 4 lb - 12, 0 kg Warrants to the original purchaser only that this Polk Audio Loudspeaker Product (the "Product") will be free from defects in materials and workmanship for a period of two (2) years from the date of original retail purchase from a Polk Audio Authorized Dealer. However, this Warranty will automatically terminate prior to the expiration of the two (2) years if the original retail purchaser sells or otherwise transfers the Product to any other party. [. . . ]