User manual PLUS V3-111

[. . . ] DATA PROJECTOR V3-131/ V3-111 User's Manual S TU TA P U S H S TA N D B Y S TA S N D B Y A U TO S O U R C E E E T C T P IM M A Z O O A T U O 4 S R 3 Q K IC E C O K S T N 2 U Q M T U E U N R E E T M E N E A C N C IMPORTANT * DLPTM (Digital Light Processing) and DMD (Digital Micromirror Device) are registered trademarks of Texas Instruments Incorporated (U. S. A. ). * DMD is an ultra-precise part developed by Texas Instruments (U. S. A. ) which takes the place of liquid crystal (in the projector). * VGA and XGA are trademarks or registered trademarks of International Business Machines Corporation (U. S. A. ). * S-VGA is a registered trademark of Video Electronics Standards Association. [. . . ] A further press returns the screen to a moving picture. FREEZE MUTE ECO STANDBY MENU RGB ENTER VIDEO CANCEL QUICK Q AUTO 1 2 3 4 ASPECT VOL KSTN ZOOM TIMER Cancelling Video and Audio Temporarily This function is used to cancel the video and audio at the same time. STANDBY MENU A press of the MUTE button will blank the picture and the sound, and the screen will take on the background color that has been set. Another press will cause a return to the original conditions. RGB ENTER VIDEO CANCEL QUICK Q FREEZE MUTE ECO AUTO 1 2 3 4 ASPECT VOL KSTN ZOOM TIMER Lamp Mode Use this if the picture is projected on a small screen and the picture is too bright or when projecting images in dark rooms. Eco (STATUS indicator is lit green) The lamp's brightness is reduced to approximately 80%, extending the lamp's service life. Normal (STATUS indicator is off) The lamp brightness is set to 100% and the screen is bright. STATUS indicator STANDBY STATUS STANDBY AUTO SOURCE Note: Frequent switching this mode can degrade the lamp. STANDBY MENU RGB ENTER VIDEO CANCEL QUICK Q FREEZE MUTE ECO AUTO 1 2 3 4 ASPECT VOL KSTN ZOOM TIMER E-29 General Operation Keystone Use this to adjust for trapezoidal (keystone) distortion of the projected image. Adjustment Method (1) Press the or KSTN button to make the left and right sides parallel. The keystone adjustment display appears when one of the buttons is pressed. STANDBY MENU RGB ENTER VIDEO CANCEL QUICK Q (2) FREEZE MUTE ECO AUTO 1 2 3 4 ASPECT VOL KSTN ZOOM TIMER (1) Press the " " button. Press the " " button. (2) Press the CANCEL button to immediately close the display. The display will close when there has not been an operation in about 10 seconds. Note: * Keystone adjustment values can be saved. * Screen examples have been drawn in an exaggerated style for the purpose of description. * Please note that depending on the projected picture and the projection conditions, it may not be possible to eliminate keystone distortion completely. Adjustment of the Volume This function adjusts the volume of the built-in speaker. The volume adjustment display appears when one of the buttons is pressed. STANDBY MENU RGB ENTER VIDEO CANCEL QUICK Q (2) FREEZE MUTE ECO AUTO 1 2 3 4 ASPECT The button increases the volume and the volume. button decreases the VOL KSTN ZOOM TIMER (2) Press the CANCEL button to immediately close the display. The display will close when there has not been an operation in about 10 seconds. Note: * Adjustment of the volume will not produce any sound unless an image is being projected. (1) E-30 General Operation Enlargement of the Image and Video Movement This function digitally enlarges the personal computer image and video image. The zoom display appears when the ZOOM button is pressed. STANDBY MENU RGB ENTER VIDEO CANCEL QUICK (2) (3) Q FREEZE MUTE ECO AUTO 1 2 3 4 ASPECT VOL KSTN ZOOM TIMER (1) Each press of the button enlarges the image and each press of the button makes the image smaller (returning it to 1:1). Zoom 0 Zoom 21 (No enlargement) (Approximately 2 times enlargement) (2) Pressing the SELECT buttons on the remote control at the time of the zoom operation will cause the display position to move. (There will not be any movement when zoom is at 0. ) Zoom 21 Zoom 21 (Approximately 2 times enlargement) (Movement) (3) Press the CANCEL button to immediately close the display. The display will close when there has not been an operation in about 10 seconds. Note: After magnifying the image, be sure to use the ZOOM button to bring the gauge value back to "0". The image can also be moved in the following circumstances. · · When "Aspect" is set to "Real" by the signal of the personal computer, and the input resolution is higher than the display resolution of the projector. When "Aspect" is set to "Zoom" by the video signal. Note: * Zoom and image movement functions are cancelled when the input is switched. * The greater the zoom enlargement, the less distinct the image will appear. The reason for this is that the dots are being digitally corrected so that they are not conspicuous. * Movement of the screen will not be possible when the menu screen is being displayed. E-31 General Operation Using the Presentation Timer The presentation is given while checking the timer displayed on the screen. The display will close when an operation has not been made for about 10 seconds. STANDBY MENU (2) RGB ENTER CANCEL button (3) VIDEO CANCEL QUICK Q FREEZE MUTE ECO AUTO 1 2 3 4 ASPECT VOL KSTN ZOOM TIMER (1) [Timer settings display] Press the CANCEL button to close the display immediately. The setting contents are "Off" and from 10 to 60 minutes (in 10-minute intervals) Settings can also be made with the SELECT buttons. (3) Press the ENTER button and start the timer. · The display of the timer setting will close, the display of the timer will appear and simultaneously the timer will start. [. . . ] Note that lamp life will be extended when the projector is often used in Eco mode. (The rated service life of the lamp means the average value of lamp life for lamps that have been manufactured over a long period, and it is derived from test conditions at this company. ) · When the life of the lamp is exceeded, the STATUS indicator lights a steady red and the message [Replace the Lamp Cartridge] is displayed on the screen. · If the projector is used another 100 hours after the lamp's service life is reached, the power is set to the standby mode and no longer turns on. · Contact a store that sells the V3-131/V3-111 for a replacement lamp. [. . . ]