User manual PLUS U5-332

[. . . ] DATA PROJECTOR User's Manual ZO 2 O M 4 R E TIM / K L LIC E -C C R AN C M U TE Q K R A U TO O E Q U IC S E LA ID V IMPORTANT * DLPTM (Digital Light Processing) and DMD (Digital Micromirror Device) are registered trademarks of Texas Instruments Incorporated (U. S. A. ). * VGA and XGA are trademarks or registered trademarks of International Business Machines Corporation (U. S. A. ). * S-VGA is a registered trademark of Video Electronics Standards Association. * Microsoft, Windows, and PowerPoint are registered trademarks of Microsoft Corporation (U. S. A. [. . . ] * Movement of the screen will not be possible when the menu screen is being displayed. E-32 General Operation Using the Presentation Timer The presentation is given while checking the timer displayed on the screen. The display will close when an operation has not been made for about 10 seconds. STANDBY LASER RGB VIDEO AUTO MENU QUICK (2) [Timer settings display] ENTER Q R-CLICK/ CANCEL CANCEL button (1) Press the CANCEL button to close the display immediately. The setting contents are "Off" and from 10 to 60 minutes (in 10-minute intervals) Settings can also be made with the SELECT buttons. (3) FREEZE MUTE TIMER 1 VOL 2 ZOOM 3 4 (3) Press the ENTER button and start the timer. · The display of the timer setting will close, the display of the timer will appear and simultaneously the timer will start. Gauge (Blue) [Timer Display] The blue gauge indicates the remaining time. When the remaining time is "0" (Gray) · Press the ENTER button to restart the timer. Moving the Position of the Timer Display The SELECT buttons on the remote control permit movement within the movable range of the timer display. Movable Range of the Timer Display Note: * The timer display will be closed while the menu or the quick menu is displayed, and while a message is displayed; however, the timer will still be operating at such times. * While the presentation timer is being displayed, screen movement will not be possible in the zoom mode. E-33 General Operation Using the Laser Pointer The remote control unit's laser pointer can be used to point to the section currently being explained, making presentations more effective. CAUTION Do not look at the laser pointer's light source. Pointing the laser beam at the eyes could lead to reduced vision or vision impairment. · Do not let children use the laser pointer. This label is located on the side of the remote control. Operation The red laser beam is emitted from the tip of the remote control unit while the LASER button is pressed in. Point the remote control unit's transmitter in the direction you want to indicate. The laser beam turns off when you release your finger from the LASER button. S TA N D B Y R G B M E N U V ID E O A U TO Q U IC LA S E R E N TE R FR EE ZE / K L LIC E -C C R AN C Q K M U TE TIM 1 V O L E R 3 2 4 ZO O M LASER Note: If a button on the remote control unit is held in continuously for approximately 30 seconds, signal transfer will be suspended. Also, to use the jog button after signal transfer has been suspended, first press any other button, then press the jog button. E-34 General Operation Performing Mouse Operations on the Computer with the Remote Control Unit When a computer and the projector are connected, mouse operations can be performed on the computer using the projector's remote control unit. When projecting images from the computer, the projector can be operated and mouse operations on the computer performed with the same remote control unit, making for efficient presentations. Connecting the computer and projector Use the USB cable included with the projector to connect the computer's USB (type A) connector to the projector's MOUSE connector. Note: * Be sure to plug the cable in securely. * Depending on the type of connection, the computer's operating system, etc. , it may be necessary to change settings or restart the computer after making the connections. USB connector USB cable (mini B to A type) (Supplied item) Functions of the mouse function buttons When operating, point the remote control unit's transmitter towards the remote control sensor on the projector. L-CLICK button (on back) Press this to perform the left-click operation. LASER VIDEO AUTO STANDBY RGB MENU QUICK JOG buttons These move the computer's pointer in the corresponding direction. R-CLICK button Press this to perform the right-click operation. Q ENTER R-CLICK/ CANCEL FREEZE MUTE TIMER 1 VOL 2 ZOOM INFORMATION The R-CLICK/CANCEL button is used for both the projector and mouse function. When the R-CLICK/CANCEL button is pressed while a menu is open, the menu is closed. 3 4 Note: Connections with USB Cables * For PC/AT compatible computers, this function cannot be used with operating systems other than Windows 98SE, Me, 2000 and XP. For Macintosh computers, this function cannot be used with operating systems other than OS 9 and later. * When the cable is disconnected and then reconnected to the USB port of the personal computer or the MOUSE connector of the projector, allow at least 5 seconds before reconnecting. Do not repeatedly disconnect and reconnect the cable in a momentary fashion. [. . . ] The rated service life of the lamp is about 2000 hours (when used in normal mode only). This could be shortened depending on conditions of use and other factors. Note that lamp life will be extended when the projector is often used in Eco mode. (The rated service life of the lamp means the average value of lamp life for lamps that have been manufactured over a long period, and it is derived from test conditions at this company. ) · When the life of the lamp is exceeded, the STATUS indicator lights a steady red and the message [Replace the Lamp Cartridge] is displayed on the screen. [. . . ]