User manual PLAYMOBIL MAISON DE VILLE

[. . . ] Connect the supply pipe by screwing it to a cold water tab using a ¾ gas threaded connection (see figure). Before performing the connection, allow the water to run freely until it is perfectly clear. Connect the other end of the water inlet hose to the washing machine, screwing it onto the appliance’s cold water inlet, situated on the top right-hand side on the rear of the appliance (see figure). The water pressure at the tap must be within the values indicated in the Technical details table (on the next page). [. . . ] € If the appliance has to be moved, work in a group of two or three people and handle it with the utmost care. € Before loading laundry into the washing machine, make sure the drum is empty. Disposal • Disposing of the packaging materials: observe local regulations so that the packaging may be re-used. € The European Directive 2012/19/EU on Waste Electrical and Electronic Equipment, requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. 5 Description of the washing machine and starting a wash cycle Control panel GB button with indicator light WASH CYCLE PROGRESS ON/OFF TEMPERATURE button DISPLAY LID LOCKED indicator light WASH CYCLE knob SPIN SPEED button START/PAUSE FUNCTION buttons with indicator lights button with indicator light CONTROL PANEL LOCK button with indicator light ON/OFF button with indicator light: switches the machine on and off. If the indicator light is illuminated, this indicates that the machine is switched on. SPIN SPEED button: sets the spin speed or exclude the spin cycle completely (see “Personalisation”). TEMPERATURE button: sets the temperature or the cold wash cycle (see “Personalisation”). DISPLAY: indicates the time remaining for the selected wash cycle and, if a delayed start has been programmed, the time remaining until the start of the wash cycle. The actual duration can vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected. 1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 2 with a temperature of 60°C. This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at 60°C. 2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 3 with a temperature of 40°C. This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at 40°C. For all Test Institutes: 2) Long wash cycle for cottons: set wash cycle 3 with a temperature of 40°C. 3) Long wash cycle for synthetics: set wash cycle 4; with a temperature of 40°C. Mix 15’(wash cycle 5) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and therefore saves both energy and time. By selecting this wash cycle (5 at 30°C), it is possible to wash different fabrics together (except for wool and silk items), with a maximum load of 1. This is a silent cycle which can be run at night, when the electricity prices are lower. At the end of the cycle the machine stops while there is still water in the drum; to spin and drain the laundry press the START/PAUSE button; alternatively the machine will perform the spin cycle and drain the water automatically after 8 hours. [. . . ] Compartment 1: Detergent for pre-wash compartment 2: Detergent for the wash cycle (powder or liquid) It is recommended that you place liquid detergent directly into the compartment using the appropriate dosing cup. ) When pouring the softener in compartment 3, avoid exceeding the “max” level indicated. The softener is added automatically into the machine during the last wash. At the end of the wash programme, some water will be left in compartment 3. [. . . ]