User manual PLANTRONICS VOYAGER 510S

[. . . ] Select the position that provides the best sound quality for both you and your co-worker. During this call you should also adjust the Listen and Speak Volume as described next. Once set, the configuration dial will not require any further adjustment. 8 A B PLACING A CALL Placing a call on your corded telephone: Lift the handset and then press either the Call Control button on the headset (A) or base unit (B). If you do not obtain a dial tone, check that the Configuration Dial is set correctly as described on page 8. [. . . ] The installation of the Handset Lifter is described in the user guide that is supplied with it. MAKING A CALL USING THE LIFTER Press the Call Control Button on the headset or base unit. You will then hear a dial tone in your headset and can proceed to make a call as normal. When you have finished your call press the Call Control Button on either your headset or base unit. The handset lifter then lowers the handset to end the call. RECEIVING A CALL USING THE LIFTER When a new call is received the telephone rings as normal, but in addition, a ring alert will be heard in your headset. Note: This additional call alert is only active when the Handset Lifter is connected. To answer the call press the Call Control Button on either the headset or the base unit. The lifter will then raise the telephone handset off the hook and you will then be able to talk to the caller. When you have finished your call press the Call Control Button on either your headset or base unit. The handset lifter then lowers the handset to end the call. 12 SWITCHING FROM HEADSET TO HANDSET WHEN USING THE LIFTER If during a call you are using your headset and want to switch to the telephone handset, remove the handset from the Lifter, then press the Call Control Button on either your headset or the base unit. The Lifter will lower and you will then be able to continue the call using the handset. SWITCHING FROM HANDSET TO HEADSET WHEN USING THE LIFTER If during a call you are using the telephone handset and want to switch to your headset, press the Call Control Button on either the headset or the base unit. The Lifter will raise and you will be able to continue the call using your headset. When the call is finished press the Call Control Button on either your headset or base unit. The Lifter will lower the handset and end the call. INTELLISTANDTM ENABLE/DISABLE When the Voyager 510 Bluetooth® Headset System is used in conjunction with a Plantronics Handset Lifter, you can enable the IntelliStandTM feature. The IntelliStandTM senses when the headset has been removed or replaced in the Voyager 510 System Base unit, automatically activating the lifter to answer or end a call. The IntelliStandTM feature is disabled when the switch is in position I (as shown) or enabled when the switch is in position II. Note: Docking the headset always ends the call regardless if IntelliStandTM is enabled or disabled. 13 AUDIBLE WARNINGS OUT OF RANGE WARNING As you walk away from the base unit you will eventually reach the system operating range limit. One high tone followed by a triple tone when back in range On hearing the edge of range alert you should walk closer to the base unit to ensure call quality is maintained. The call will be re-established on walking back in range If you remain out of range for more than 10 minutes the system will drop the call permanently. If using a Plantronics Handset Lifter the handset will be replaced and the call terminated. LOW BATTERY WARNING When the headset battery is running low, an audible warning will be heard through the headset as a single beep repeating every 20 seconds. The headset Status Indicator will also flash red when the battery needs to be recharged. You should recharge the headset immediately. MUTE ACTIVE WARNING When muted, the headset will sound two tones every 30 seconds. 14 PAIRING The Voyager 510 Bluetooth® Headset System is supplied with the Headset and Base Unit factory paired to each other. However, if you have purchased a Voyager 510 System Base Unit or if you wish to use a replacement headset with your existing base unit the units must be paired as follows: 1. [. . . ] If the volume is still too low, select another Rx Slide Switch setting as described on page 10. Incorrect Configuration Dial setting for your telephone Try other Configuration Dial settings on the base unit. 18 PROBLEM Callers cannot hear me. Solution To disable the IntelliStand function move the IntelliStandTM Switch to position I (Off). PROBLEM Headset loses response to button presses Headset needs a reset. A hardware reset of the headset can be accomplished by a simultaneous long press of the POWER/MUTE and SPEAK VOLUME DOWN keys. 20 Plantronics Ltd Wootton Bassett, UK Tel: 0800 410014 +44 (0)1793 842200 Plantronics B. V. [. . . ]