User manual PLANTRONICS SAVI GO WG100/B

[. . . ] 12 Battery life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Help for USB adapter settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 PC panel screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Advanced settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Calls will be re-established when you walk back into range. Pairing headset to USB adapter The headset and USB adapter are supplied paired to each other. However, if you wish to use a replacement headset with your existing USB adapter, the units can be paired to each other by the following method: 1 Ensure your replacement headset is fully charged. Low battery warning A repeating high/low tone pair every 10 seconds indicates the battery is low. You should recharge the headset immediately. 2 Power the headset off by pressing and holding the call control button for six seconds. The headset indicator light will be red for four seconds. 3 Place the headset in pairing mode by pressing and holding the call control button until the indicator light flashes red and blue. Checking battery level You can check the battery level by moving the call control button to the volume down position, then pressing inwards and holding for two seconds. The headset indicator will flash red to indicate the remaining battery charge level. One red flash = low charge level Two red flashes = medium charge level Three red flashes = high charge level 4 Place the USB adapter in pairing mode by pressing and holding the pairing button on the adapter for two seconds. The pairing light will flash red and blue. 5 When the pairing light on the USB adapter goes solid blue, the headset and the USB adapter are paired. turning headset indicator blue flash on/off By default, the headset indicator flashes blue to indicate the headset state as described in the section Headset indicator lights and tones. This feature may be disabled by moving the call control button to the volume up position, then pressing inwards and holding for two seconds. Repeat this operation to turn the headset blue flashing indicator back on. notE: Take care when pairing the USB adapter. Please "press" with both fingers rather than push on the USB adapter to avoid damage to the USB adapter or USB port. mute warning When mute is activated, you will hear a single low tone which will repeat every 30 seconds. Plantronics Savi User Guide 10 5 Using your headset with your Bluetooth mobile phone ® Pairing your headset to your Bluetooth mobile phone 1 turn on your mobile phone and enable Bluetooth. For most phones, select Settings>tools>Connections> Bluetooth>on. See your phone's user guide for more information. notE The headset will stay in pairing mode for three minutes. 4 Use the commands on your phone to locate the headset. For most phones select Settings>tools>Connections> Bluetooth>Search>Savi Go WH100. See your phone's user guide for more information. 5 When prompted for a password, enter 0000 (4 zeros). The headset indicator light will flash blue when paired successfully. notE For detailed pairing instructions for popular mobile phones, visit: www. plantronics. com/easytopair. 2 If the headset is powered on, power the headset off by pressing the call control button in for six seconds. The headset indicator light will remain solid red for four seconds to indicate that the headset is powered off. 3 Press the headset call control button in for six seconds or until the indicator light flashes red and blue alternately. Placing, answering and ending calls with your headset and Bluetooth mobile phone To place a call To answer a call To answer a call when already on an active UC application call To end a call Redial last number* Dial number on your mobile phone keypad. Short press the call control button to end the UC application call, then press again to answer your mobile phone call. Go to the "new event" tab located in the upper right of the Skype window and click on the red flag. You then will need to click on the "PerSonoSuite. exe" link to be taken to the "manage aPI access Control" screen. Battery life PerSono Suite. exe At the lower left-hand corner of the screen (and for all software screens), you will see one of the following icons indicating the approximate charge left in the headset battery. 100% 75% 50% 25% Less than 5 mins Plantronics Savi User Guide 12 Settings screen ­ headset and USB adapter The Settings screen allows you to customise the adapter and headset to your preference. The Savi Go system is supplied with the default settings and can be changed as described in the Settings column below. PerSono Suite automatically greys out parameters that do not apply to a particular Plantronics device. Settings ­ headset Feature Mute tone Ring tone ­ PC Ring tone volume ­ PC Ring tone - mobile Ring tone volume - mobile Second inbound call Settings On/off Sound 1/sound 2/sound 3 On/off Sound 1/sound 2/sound 3 On/off Ring continuously/ring once/ignore Default On Sound 2 On Sound 1 On Ring continuously Settings ­ USB adapter Feature Audio bandwidth ­ PC Ring both headset/PC Settings Wideband/narrowband On/Off Default Wideband On Help for USB adapter settings audio Bandwidth The system will support both narrowband and wideband audio from the PC. Wideband audio delivers heightened speech clarity and life-like fidelity. However, wideband audio consumes more battery power and has more stringent access criteria, which reduces the number of systems that can be deployed in a small area. [. . . ] Press the call control button for approximately 4 seconds until you hear a tone or see the indicator glow blue. See "Fitting headset" on page 7. Audio quality is poor. Your headset is out of range. Move the headset closer to the Bluetooth phone. Callers cannot hear me. Make sure that the headset is sitting correctly on your ear with the boom pointing towards the corner of the mouth. See "Fitting headset" on page 7. My headset falls off my ear. Make sure that the headset is sitting correctly on your ear with the boom pointing towards the corner of the mouth. [. . . ]