User manual PLANTRONICS SAVI GO

[. . . ] 11 Checking Battery Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Mute Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2 Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To conserve power you may optionally power the headset off, by pressing and holding the call control button for six seconds. The headset indicator light will be lit red for four seconds to confirm that the headset is powered off. To power the headset back on press and hold the call control button for four seconds when the headset indicator will light blue for two seconds, then flash red a number of times to indicate the remaining battery charge (see Checking the Battery Level). Indicator Light Call Control Button Placing, Answering, and Ending Calls with microsoft office Communicator To place a call To answer a call on the headset To answer a call when already on an active call on your mobile phone To end a call on the headset Dial number using Microsoft Office Communicator* Short press call control button on headset Short press the call control button once to end the mobile phone call then press again to answer your Microsoft Office Communicator call Short press call control button on headset *Consult Microsoft Office Communicator Help for more information on how to place a call. notE You can also answer calls directly from Microsoft Office Communicator by clicking on the Call Alert that appears on your PC screen. In this case the call will be directed to the default speakerphone which may not be your headset. Consult Microsoft Office Communicator Help for more information. Plantronics Savi User Guide 9 muting a Headset Call To mute a call, press and hold the call control button down (in the volume down position) for two seconds. To unmute a call, push and hold the call control button down (in the volume down position) for two seconds. You will hear a high/ low tone pair indicating the mute is deactivated. Volume Down Button USB Adapter Indicator Light USB Adapter Status Headset in talk mode Base and headset pairing Indicator Light Flashes blue Flashes red and blue Headset Indicator Lights and tones Headset Status Headset charging Headset fully charged Headset battery low Headset ready Incoming call Active call Headset Indicator Light Solid red Off Flashes double red Slow blue flash (every 10 sec. ) Flashes purple Flashes blue Plantronics Savi User Guide 10 out of range Warning If you are on a call you will hear the audio degrade as you move out of range. Calls will be re-established upon walking back into range. Pairing Headset to USB Adapter The headset and USB adapter are supplied paired to each other. However, if you wish to use a replacement headset with your existing USB adapter, the units can be paired to each other by the following method: 1 Ensure your replacement headset is fully charged. Low Battery Warning A repeating high/low tone pair every 10 seconds indicates the battery is low. You should recharge the headset immediately. 2 Power the headset off by pressing and holding the call control button for six seconds. The headset indicator light will be red for four seconds. 3 Place the headset in pairing mode by pressing and holding the call control button until the indicator light flashes red and blue. Checking Battery Level You can check the battery level by moving the call control button to the volume down position, then pressing inwards and holding for two seconds. [. . . ] Press the call control button for approximately 4 seconds until you hear a tone or see the indicator glow blue. See "Fitting Headset" on page 7. Audio quality is poor. Your headset is out of range. Move the headset closer to the Bluetooth phone. Callers cannot hear me. Make sure that headset is sitting correctly in ear with boom pointing towards corner of mouth. [. . . ]