User manual PLANTRONICS S12

[. . . ] In order to have phone service during a power outage, have another telephone available that is powered only by the telephone line. Avoid using a telephone (other than a cordless type) during an electrical storm. Do not use the telephone to report a gas leak in the vicinity of the leak. SAVE THESE INSTRUCTIONS S12 QUICK START GUIDE 1 1 2 3 4 5 6 7 8 9 Left Side View 10 11 Identify the Components Headset Holder Compatibility Slide Switch S12 Amplifier Headset Indicator (Green) Power Indicator (Green) Mute Indicator (Red) Listen Volume Control Mute Button Headset/Handset Button Speak Volume Control Speak Volume Master (Hi, Low) Switch Cord (Phone to Amplifier) AC Power Adapter 12 Over-the-Head 13 14 2 Attach Amplifier to Telephone Right Side View Adjustable Headband Headset Assembly Clothing Clip Headset Plug Microphone Boom Ear Cushion Assembly Earloop Pivot Ball Ring FireflyTM In-Use Indicator Over-the-Ear 15 16 17 18 2. 1 Unplug your telephone handset cord from the telephone base. 2. 1 2. 2 Plug your telephone handset cord into the S12 amplifier handset jack. 2. 3 Connect the cord 21 between the telephone base jack on the S12 amplifier and your telephone base. [. . . ] 2. 3 Connect the cord 21 between the telephone base jack on the S12 amplifier and your telephone base. 2. 4 Plug the headset plug into the headset jack. Back View 19 20 2. 4 2. 2 2. 3 21 22 2. 5 Route the headset cord through the cable management channel on the bottom of the amplifier (not shown). 2. 6 Snap in the headset holder 10 (not shown). 23 AC Power Adapter Jack Headset Jack Handset Jack Telephone Base Jack 24 25 26 2. 7 Plug the AC power adapter into the AC power adapter jack and plug into a standard AC wall output. 2. 7 Over-the-Head. . . . . . . . . . . . converts to. . . . . . . . . . . . Over-the-Ear 3 Set Amplifier Compatibility Slide Switch 3. 1 Put on headset and press the headset button. 3. 2 Lift the telephone's handset off the cradle and place it on your desk. 3. 4 If you don't hear a dial tone, adjust the compatibility slide switch following this process: 1. Slide the compatibility slide switch until you hear a clear dial tone. 3. 1 4 1. Make a Test Call 4. 1 Verify that the mute button is off. The mute indicator should not be illuminated 4. 2 Remove the phone handset from the cradle and place on your desk. 3. 2 If you do not hear a dial tone in the headset, press the headset button. 4. 5 If your friend cannot hear you, or you hear a buzz or hum, try changing the compatibility slide switch. 4. 6 Adjust how loud you sound to the other party by adjusting the speak volume control. 4. 7 If you sound too loud, move the speak volume master switch to its lower setting and adjust the speak volume control. 4. 8 After completing the call, return the handset to its cradle. 4. 6 4. 21 4. 4 4. 5 4. 1 There may be multiple settings with a dial tone. The telephone company may make changes in it's facilities, equipment, operations or procedures that could affect the proper functioning of your equipment If they do, you will be notified in advance in order for you to make necessary modifications to maintain uninterrupted service. INDUSTRY CANADA NOTICE Terminal Equipment Notice: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. Notice: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment itself. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five. Radio Equipment The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. "Privacy of communications may not be ensured when using this telephone". PARTS Headset Holder 65217-01 LIMITED WARRANTY for Plantronics Commercial Products Purchased in the US and Canada Cord (phone to amplifier) 65218-01 AC Power Adapter 45671-01 Adjustable Headband 43298-01 Headset Assembly 65219-01 345 Encinal Street Santa Cruz, California 95060 (800) 544-4660 Pivot Ball Ring 45650-03 www. plantronics. com © 2002-2003 Plantronics, Inc. Plantronics, the logo design, Plantronics and logo design combined, Call Clarity, Firefly and SoundGuard Plus are trademarks or registered trademarks of Plantronics, Inc. 5, 210, 791, D394, 437 & D403, 327; Finland 20183 & 20184; GB Regd. Des. No. [. . . ] "Privacy of communications may not be ensured when using this telephone". PARTS Headset Holder 65217-01 LIMITED WARRANTY for Plantronics Commercial Products Purchased in the US and Canada Cord (phone to amplifier) 65218-01 AC Power Adapter 45671-01 Adjustable Headband 43298-01 Headset Assembly 65219-01 345 Encinal Street Santa Cruz, California 95060 (800) 544-4660 Pivot Ball Ring 45650-03 www. plantronics. com © 2002-2003 Plantronics, Inc. Plantronics, the logo design, Plantronics and logo design combined, Call Clarity, Firefly and SoundGuard Plus are trademarks or registered trademarks of Plantronics, Inc. 5, 210, 791, D394, 437 & D403, 327; Finland 20183 & 20184; GB Regd. Des. No. 2073246 & 2073247; Sweden 64 176 & 64 177 Ear Cushion Assembly (Leatherette Assembly) 46186-01 · This warranty covers defects in materials and workmanship of Commercial Products manufactured, sold or certified by Plantronics which were purchased and used in the United States and Canada. [. . . ]