User manual PLANTRONICS HL10 LIFTER FOR AVAYA AMPLIFIERS

[. . . ] When using telephone equipment and accessories, basic safety precautions should be taken to reduce risk of fire, electric shock, and to persons including the following: 1 The intended purpose of this HL10 Handset Lifter is to lift and lower the telephone handset in conjunction with Avaya amplifiers LCS10, LKA10, and Avaya products manufactured for use with the HL10 Handset Lifter. 2 To ensure safe operation, install, adjust and operate the HL10 Handset Lifter according to these instructions. [. . . ] 5 Do not allow anything other than the telephone handset to rest on this product or locate it in an area where normal operation can be hampered. The product may fall causing serious damage to the product. SAVE THESE INSTRUCTIONS 61851_01. qxd TECHNICAL SUPPORT For assistance and accessibility information call the Avaya Technical Assistance Center (TAC) (800) 628-2888 Sunday 5P. M. Pacific Standard Time Avaya Technical Assistance Center After you have completed the instructions in the Quick Start Guide and reviewed the Troubleshooting Section (the inside foldout) and still have questions, please contact our Technical Assistance Center. 12/6/01 61851-01 (12. 01) 12:31 AM Page 1 HL10 Handset Lifter Accessory Quick Start & Information Guide 61851_01. qxd 12/6/01 12:31 AM Page 2 HL10 HANDSET LIFTER ACCESSORY 1. 2 Lifting Pad Back and Underside View 1. 3 Lifter Height Switch 1. 1 Motor Housing 1. 4 Accessory Jack Position and Test Lifter (Do not remove the mounting tape backing until directed to do so. ) 2. 2 2. 1 1. 5 Power Cord Top View Identify Lifter Parts Make and Receive Calls 4. 1 Mount Lifter 4. 2 3. 1 Mounting Tape Underside View QUICK START GUIDE The HL10 Handset Lifter accessory is designed to automatically lift the telephone handset off the cradle when activated by your Avaya amplifier. 4 Make And Receive Calls 4. 1 Put on your headset and press the talk button. 4. 2 This action directs the lifter to raise the telephone handset from the cradle and activates the telephone line. To make a call, use your telephone or remote dial pad to dial the number. When receiving a call, the ring detector senses a ring from your telephone and transmits it to your remote unit or headset. You can answer the call by pressing the talk button and begin talking through your headset. Note: For remote ring detection to work you may need to increase the telephone ringer volume. In some cases, telephones with multiring tone choices may require trying several tones to choose the most effective sound for ring detection. 1 Identify Lifter Parts 1. 1 Motor Housing 1. 2 Lifting Pad 1. 3 Lifter Height Switch (low, medium, or high) 1. 4 Accessory Jack 1. 5 Power Cord (non-removable) 2 Position And Test Lifter 2. 1 Plug the power cord into your Avaya amplifier accessory jack and position the lifter under your telephone handset towards the earpiece. You may need to position the lifter slightly differently for optimal lifting. (Tip: Remove only a tiny piece of the mounting tape backing to temporarily stick the lifter into a test position. ) TROUBLESHOOTING I cannot hear a dial tone s Press the talk button to activate your amplifier. s Set lifter height switch to a higher setting, if it`s not opening the hookswitch. [. . . ] You should hear a dial tone in the headset if the telephone handset is raised high enough. 3 Mount Lifter 3. 1 Mounting Tape Once you have determined the best position for the lifter, remove the mounting tape backing on the top or side to best adhere the lifter to your telephone. On a few telephones both the top and side mounting tapes must be used to firmly grip the telephone. [. . . ]