User manual PLANTRONICS HL1 / HL2 LIFTER

[. . . ] HL1_HL2 11/17/03 6:39 PM Page 1 HL2 DIAGRAM 2 HL2 TELEPHONE HANDSET LIFTER ACCESSORY A B C HL2 TELEPHONE HANDSET LIFTER ACCESSORY HARDWARE SETUP FOR THE A20 TELEPHONE HEADSET AMPLIFIER Snap the Lifter Motor Assembly to the A20 accessory deck. with the A20 Adapter Housing C HL1 5 3 HL1 HL2 1 D Connect the Adapter Power Plug to the aux jack of the A20 amplifier. The aux jack on the A20 amplifier is normally used for the on line Indicator (OLI). [. . . ] contact Plantronics at (800) 544-4660 and in Canada call (800) 540-8363. If you need additional i nformation, please contact our service centers at the numbers provided. · We will, at our option, repair or replace the Products that do not conform to the warranty. We may use functionally equivalent reconditioned/ refurbished/remanufactured/pre-owned or new Products or parts. · This warranty extends to you only if you are the end user with the original purchase receipt. · This warranty lasts for two years from the date of purchase of the Products. · This warranty covers defects in materials and workmanship of Commercial Products manufactured, sold or certified by Plantronics which were purchased and used in the United States and Canada. for Plantronics Commercial Products Purchased in the US and Canada LIMITED WARRANTY Printed in the U. S. A. 345 Encinal Street Santa Cruz, California 95060 www. plantronics. com 800. 544. 4660 65688-01 ©10·2003 P l a n t r o n i c s I n c . Models HL1 & HL2 Telephone Handset Lifter Accessory User Guide A D 18890 Plx. HL1_HL2 11/17/03 6:39 PM Page 2 HL1 TELEPHONE HANDSET LIFTER ACCESSORY HL1 TELEPHONE HANDSET LIFTER ACCESSORY TROUBLESHOOTING I CANNOT HEAR A DIAL TONE On the CA10 amplifier, press the talk button on the CA10 base or amplifier remote unit. HARDWARE SETUP FOR THE CA10 CORDLESS TELEPHONE HEADSET AMPLIFIER Slide the Lifter Motor Assembly · into the LHL1 Base ² until it locks in. Connect the Adapter Power Plug ³ to the lifter jack on the base of the CA10 Cordless Telephone Headset Amplifier. Loosen the Lifter Arm screw and insert the Lifter Arm ´ into the shaft. Position your telephone on the Lifter Base ² so that the lifter arm is under the handset, near the earpiece. You may need to manually readjust the lifter arm to the position shown in D . Depress the Talk button on the CA10 base or remote unit and the Lifter will automatically pickup your handset so that you hear a dial tone. Connect the Ring Detector Cable ¿ to the Ring Detector Jack ¾ located on the back of the Lifter Assembly ·. Remove the tape from the Ring Detector Sensor and attach the sensor to a position closest to the telephone ringer/speaker. The Ring Detector Sensor is a little cylindrical microphone located at the end of the Ring Detector Cable ¿. Make sure your remote unit "ringer" switch is in the "on" position. You are now ready to receive calls up to 150 feet from your telephone. B A C LIFTER OPERATION MAKING AND RECEIVING A CALL (Near your telephone) Put on your headset and depress the talk button on the CA10 base or remote unit. This action activates the lifter to take the telephone handset off the hook. When your call is complete, push the talk button again on the CA10 base or remote unit. [. . . ] Your phone's ringer volume may need to be turned up. LIFTING ARM HEIGHT VARIES Tighten the lifting arm retaining screw. Check the positioning of the phone on the base to be sure it has not shifted. Readjust the arm in rest position. HL1 DIAGRAM HL1 HL1 er Pow Talk CA10 Cha rge NEL CHAN TALK ­ ME VOLU MUTE + B HL2 A HL2 A20 C D HL1 DIAGRAM HL1 DIAGRAM KEY 7 1 2 8 3 9 4 5 6 Ringer Detector Jack Accessory Jack Adapter Power Line HL1 Lifter Base Lifter Arm P/N 46778-01 HL1 Ringer Detector and cable P/N 46780-01 HL1 Expandable Base Lifter Motor Assembly HL1 Adapter Power Plug [. . . ]