User manual PLANTRONICS CA12CD DECLARATION OF CONFORMITY

[. . . ] 30 units placed 45. 7 centimetres apart), the range could decrease to 3 metres. 1. 3 Plug the modular connector on the console interface cable into the modular jack on the back of the base unit. 1. 4 Plug the AC adapter into the wall outlet, and plug the round power connector into the back of the base unit. When the battery pack is installed or changed, the on-off Indicator will begin to flash slowly as soon as the unit is ready for use. [. . . ] 1. 7 Place CA12CDs at least 30. 5 centimetres away from CRT-type computer monitors. 2. 1 To attach the battery pack to the remote unit, simply slide the battery pack onto the remote unit and snap it into place. The larger well allows charging of the battery while it is attached to the remote unit. The smaller well allows charging of a spare battery pack all by itself. 2. 3 Insert the remote unit and the spare battery pack into their respective charging wells. The charging indicators will flash while the battery packs are charging. 2. 4 When a battery pack is charged, its charging indicator will stop blinking and glow steadily. 2. 5 The on-off indicator on the remote unit will begin to flash as soon as the unit is ready for use. This may require about 45 seconds while the remote unit determines and selects the most reliable radio channel. 2. 7 To maximise the life of the battery pack, turn the remote unit off and place it into the charging well when not in use. Prior to being used, battery packs must be charged for at least one hour or until the charging indicator changes from blinking to continuously on. The radiated output power of this internal wireless radio is far below radio frequency exposure limits. Nevertheless, the wireless radio shall be used as described in the manual. The internal wireless radio operates within guidelines found in radio frequency safety standards and recommendations, which reflect the consensus of the scientific community. Plantronics therefore believes the internal wireless radio is safe for use by consumers. The level of energy emitted is far less than the electromagnetic energy emitted by wireless devices such as mobile phones. However, the use of wireless radios may be restricted in some situations or environments, such as on board aeroplanes. If you are unsure of restrictions, you are encouraged to ask for authorisation before turning on the wireless radio. TECHNICAL ASSISTANCE Visit our web site at www. plantronics. com/support for technical support including frequently asked questions, compatibility and accessibility information. The Plantronics Technical Assistance Center (TAC) is also ready to assist you on 800-544-4660. SuppLIES AND ACCESSORIES AC Adapters Remote North America (shown): 64401-01 European Union: 47249-02 United Kingdom: 64784-01 Australia: 66804-01 North America 90224-01 (UPCS) 90224-02 (DECT) Function Causes relay closure in base unit that "keys up" user's radio Enables or disables locking operation of the PTT Switch Toggles the RF link between the idle-locked and enabled states Adjusts the listen (receiving) sensitivity in 2-dB steps Adjusts the listen (receiving) sensitivity in 6-dB steps Talk (sending) fine-adjust volume Adjusts the talk (sending) control momentary push buttons sensitivity in 2-dB steps on base unit top Talk (sending) coarse-adjust volume control slide switch on base unit bottom Adjusts the talk (sending) output for carbon, electret or dynamic mic applications VISIBLE INDICATORS Name Remote unit: green on-off indicator Aspect 1) Flashing slowly to conserve battery charge. [. . . ] 1) On continuously when the base unit is connected to power via the AC adapter. 2) On steadily when battery is fully charged or during top-off charging. 3) Rapidly flashing to indicate a fault condition (remote charge indicator only). Function 1) Indicates that the RF link between the remote and the base is enabled. Shows PTT status. Base unit: green base power indicator Base unit: green talk indicator Base unit: orange charging indicators Console interface cable 68331-01 6 wire, modular-to-PJ7 cable assembly Connectors other than the PJ7 are available upon request Battery Pack 90225-01 Shows battery and charger status. WEEE DISPOSAL INFORMATION Products labelled with the symbol of a crossedout wheelie bin as shown below are electrical and electronic equipment. [. . . ]